40, WMDC Industrial Complex; Ambethan Road, Kharabwadi; Chakan, Tal.: Khed, Dist.-Pune(Pin410 501) ; (+91) 213 - 55 22 03; (+91) 213 - 55 21 61 Indonesia; P.T. Kawan Lama Sejahtera pt; Gedung Kawan Lama Jl. Puri Kencana No. 1; Meruya - Kembangan; Jakarta 11610; ( + 62) 21 - 5 82 82 82; (+62) 21 - 5 82 55 88; kawanlama@kawanlama. com Iran; Kalavaran Co. Ltd.; P.O.Box: 11365 - 4653; ; Tehran; (+98)21 - 67 00 862/67 01 383; (+98) 21 - 67 09 427; kalavaran@kalavaran. com Israel; Proter + Cohn Ltd; T

duty cycle 60 % 60 % 100% duty cycle at 250 A 270 A Mains fuse T 16 A T 20 A Cooling F F Insulation class H H Protection class IP 21 IP 21 IP 21 Wire feed - - 4 roller drive Dimensions (Ixwxh) 1080x423x533 1080x423x533 737x420x240 Weight (with SDV) 130.3 kg 144.1 kg 24 kg Temperature range: operation -10 to +40 °C -10 to +40 °C -10 to +40 °C storage -20 to +70 °C -20 to +70 °C -20 to +70 °C Operating conditions: relative humidity 10-80 % 10 - 80 % 10 - 80 % Recommended welding t

Attention ! Priere de lire attentivement la presente notice avant l'installation et la mise en service. Oppassen! Lees deze instructies voor de installatie en ingebruikname aandachtig door. D DEUTSCH ENG ENGLISH KONFORMITATSERKLARUNG DECLARATION OF CONFORMITY Wir erklaren in alleiniger Verantwortlichkeit, da. dieses Produkt mit We herewith declare in our sole responsibility that this product den folgenden Normen ubereinstimmt* gema. den Bestimmungen complies with the following standards* der Ric

They keep in close contact with those who know best what good welding equipment is all about: the craftspeople. That is why a Metabo welding device has everything you need. That is a promise, because in addition to designing our welding equipment from start to finish, we also produce and assemble it - from the transformer to the entire electronics. The strictest of quality checks are therefore quite normal and the five year warranty on the main transformer is a logical conclusion. Metabo. Work.

3. Unplug the power cable. 6. Maintenance This welding machine contains no userserviceable parts. Depending on dust accumulation the dust should be blown out from the machine with dry and oil-free compressed air every 4 - 6 months. Periodically perform a check for visible damage. Contact a qualified electrician if any of the cables are damaged. 7. Available Accessories For special welding tasks the following accessories are available at specialised dealers – see back cover for illustrations. The

Description 600 DP A 80 Stock-No. 900 DP A 90 Stock-No. 1200/1204 DP A 120 Stock.no 1200/1204 DP P 140 Stock.no. 1 Torch body 132 762 4462 132 714 3634 132 714 3642 132 714 3650 2 O-ring 132 718 0807 132 714 3669 132 714 3669 132 714 3669 3 O-ring 132 714 3677 132 714 3677 132 714 3685 4 Plasma electrode 132 718 0785 132 714 3693 132 714 3693 132 714 3693 5 Air regulator ring, brown 132 718 0793 132 714 3707 132 714 3707 312 714 3707 6 Tip 0 1.0 132 718 0777 Tip 0 1.1 40-60 amp 13

For PA-liners with 4.7 mm outer diameter no support tube is required. 8. Attach torch lead assembly to machine and cut off (do not pinch off with cutting pliers) the PA-liner just in front of the feed roller. 9. The cutoff liner piece is installed between the wire spool and wire feed unit, to provide for easy guiding here too. 10. To thread the aluminium wire into the lead assembly temporarily remove the contact tip. Thread wire into liner. Set guide rollers to match wire diameter and pressur

Welding outside in the rain is not permitted. Mains connection x Check to see that mains voltage matches the voltage shown on the machine's rating plate. x Set welding step switch to "0" before plugging in. Shielding gas cylinder connection x Place gas cylinder onto the welding machine's cylinder rack and secure with the chain to the cylinder holder at the rear of the unit. Take off the cylinder cap and open cylinder valve briefly, facing away from your body. x Screw pressure reducer to the gas

This plasma beam quickly vaporizes metal and its high kinetic energy effectively ejects the melted material from the kerf. 5.1 Pilot Arc The pilot arc makes cutting painted or coated material simple, without the need to clean the surface for good electrical conduction. The pilot arc is ignited between the torch's electrode and the cutting tip by high frequency. The cooling gas blows the pilot arc from the tip as a needle-shaped flame, which burns through the paint or coating. The main arc can