. The welder control panel contains information regarding proper input 3 Operating Instructions GTAW Arc Welding Torch voltage and amperage. Follow the specifications on the welder front panel. . The receptacle used for the welder must be properly grounded and the welder must be the only load on the power supply circuit. The Components of TIG Welding (not included with your WT6100 TIG torch) are: 1. A constant current power supply such as the Arcitech 110 inverter technology arc welder. 2. A bot

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or Notes property damage! Retain instructions for future reference. Notas BUILT TO LAST Aluminum Welding Kit Description Model WT2531 is an aluminum welding kit designed for use on Campbell Hausfeld wire feed MIG welders (WG206X and WG208X series). This kit includes: Teflon ® wire liner (Part Number: WC403621AV) , smooth-groove drive roller (Part Number: WC5008

When the speed is to slow, the weld metal piles up and the bead is high and wide. SlAG ReMOVAl Wear ANSI approved safety glasses (ANSI Standard Z87.1) and protective clothing when removing slag. Hot, flying debris can cause personal injury to anyone in the area. After completing the weld, wait for the welded sections to cool. A protective coating called slag now covers the weld bead which prevents contaminants in the air from reacting with the molten metal. Once the weld cools to the point that

Electrodes used for shielded metal arc welding have two parts. The inner core is a metal rod or wire that should be similar in composition to the base metal. The outer coating is called flux. Various types of flux exist. Each coating is used for a particular welding situation. While the metal is molten, it can be contaminated by elements in the air. This contamination could weaken the weld. The flux coating creates a protective barrier called slag that protects the molten metal from contaminants

High humidity causes moisture condensation on electrical components. Moisture can contribute to corrosion and short electrical components. Dust and dirt in the welder retain moisture and increase wear of moving parts. Place the welder in an area that provides at least twelve inches (305 mm.) of ventilation space at both the front and rear of the unit. Keep all obstructions away from this ventilation space. Store electrodes in a clean, dry location with low humidity, such as WT2240 Electrode Co

Other positions require different techniques such as a weaving pass, circular pass, and jogging. A higher skill level is required to complete these welds. All work should be performed in the flat position if possible. For specific applications, consult an arc welding handbook. WELD PASSES Sometimes more then one pass is necessary to fill the joint. The root pass is first, followed by filler passes and the cover pass (See Figure 11). If the pieces are thick, it may be necessary to bevel the edges

These welders are equipped with infinite amperage control to accurately select the proper current needed for various welding conditions. Internal components are thermostatically protected. This welder can weld up to 1/8” steel in a single pass. Recommended electrode size is 1/16” diameter for 15 amp circuits, up to 5/64” diameter for 20 amp circuits. For replacement electrodes, call (800) 746-5641 for the nearest dealer. Unpacking When unpacking, inspect carefully for any damage that may have oc

5/64 in. (2 mm) H i g h 7 . Position the electrode to begin weld, lower the welding helmet or position the hand shield, and strike an arc. Adjust output setting as n e e d e d . 8 . When finished welding, turn welder off and store properly. Do not operate thiswelding machine with cracked or missing insulation on welding cables, electrode holder, or power cord. Every 3 months: Replace any unreadable labels on the welder. Use compressed air to blow all dust and lint from the ventilation o p e n i

Longitud del Arco - la distancia entre el extremo del electrodo y el punto de contacto con la superficie de trabajo. Metal Basico - el material que se va a soldar. Union a tope - la union de dos miembros alineados aproximadamente en el mismo plano. Crater - el vacio que se forma cuando el arco hace contacto con el metal basico. CD o Corriente Directa - corriente electrica que se deplaza en un solo sentido. La polaridad (+ o -) determina el sentido del desplazamiento. CD Polaridad Reversa - ocurr

These MIG items include but are not limited to; Contact Tips, Nozzles, Gun Liners, Drive Rollers, Felt Wire Cleaner. In addition, this warranty does not extend to any damage caused by the untimely replacement or maintenance of any of the previously listed CONSUMABLE parts. D. Any failure that results from accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions provided in the owner’s manual(s) supplied with the product. E. Pre-delivery service, i.e. as