Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
DFB-ADAPTOR-03.1 1. Quick Disconnect Feeder End may be connected directly to a Bernard adaptor by threading quick disconnect directly into adaptor. Make all necessary power, control, and gas connections. 2. Quick Disconnect Feeder End, PN 4920 is supplied with two long guide tubes (PN 478 and 479) of different I.D.’s which must be cut to the proper length. 3. Select the proper guide tube I.D. from the table below. .023-.052 Electrode Small I.D. .062-1/8 Electrode Large I.D. 4. Install taper end toward feed rolls. If electrodes below .045 are being used, it may be advisable to grind a chisel point on the tapered end to guide electrode closer to the feed rolls. 5. Procedure to determine cut length for guide tube that extends beyond quick disconnect (Refer to Illustration 1): A. Mark tube at point even with end of quick disconnect body. B. Remove guide tube. C. Cut guide tube at a point 1-1/2” toward the taper from the area marked. D. Reinstall in adaptor and tighten set screw. 6. Procedure to determine cut length for guide tube recessed within quick disconnect (Refer to Illustration 2). A. With small rule, measure amount guide tube is within quick disconnect body. B. Using formula below, cut guide tube to proper length. Shorten guide tube from end opposite taper. C. 1-1/2” minus distance measured inside the quick disconnect body equals length to be shortened. 7. Insert the guide tube in the adaptor. Check guide tube length as indicated in Illustration 3 for proper fit and tighten set screw. E-Z Feed Adaptor Kits are supplied with pre-cut guide tubes for specific machines, as indicated below. Mark Here INSTALLATION INSTRUCTIONS ILLUSTRATION 2 GUIDE TUBE WITHIN QUICK DISCONNECT Adaptor Guide Tube Power Socket Quick Disconnect Control Wires Body Gas Hose Measure ILLUSTRATION 1 GUIDE TUBE BEYOND QUICK DISCONNECT Control Wires Gas Hose Adaptor Guide Tube Power Socket Quick Disconnect Body ILLUSTRATION 3 Quick Disconnect Body PROPER GUIDE TUBE POSITION Adaptor Guide Tube Power Socket Control Wires Gas Hose 11/2” 0” 1 / 4 ” 1 / 2 ” 1 ” 1 1 / 4 ” 1 1 / 2 ” 1 3 / 4 ” 3 / 4 ” 2 ” 4820G 2 3 7 5 1 4 9 6 11 8 10 FOR USE ON ITEM PART NO. DESCRIPTION Hobart 1 4893 Body, w/Gas Barb & O-Ring Beta-Mig 2 4850 Guide Tube, Small I.D. 200-2000 3 373 Guide Tube, Large I.D. Models 17 & 19 4 1571 Gas Hose 5 4908 Socket Miller 6 5108 Adaptor Body Migman 105 7 4912 Snap Ring W/pre-cut guide 8 4942 Wire Assembly tubes 9 1930 Oetiker Clamp 10 1346 Terminals 11 396 Set Screw FOR USE ON ITEM PART NO. DESCRIPTION ESAB 1 4893 Body, w/Gas Barb & O-Ring Me-2 2 9394 Housing, Male Connector Migmaster 180 3 9395 Pin, Connector CENTURY 4 1571 Gas Hose 100, 130, 150, 160 5 4972 Socket 200, 225, 250 6 4912 Snap Ring powermate225 7 4942 Wire Assembly AIRCO 8 1930 Oetiker Clamp Dippak 250, 300 9 9713 Plastic Gland MIGhty 2E, 4HD, 10 4805 Adaptor Body IIE, IVHD 11 396 Set Screw CEMIG 169T, 200T 12 4852 Guide Tube, Small I.D. POWCON PDP1, powerdrive1, power drive1E, DAV Mig FOR USE ON ITEM PART NO. DESCRIPTION Panasonic 1 4893 Body, w/Gas Barb & O-Ring YW501FK 2 4958 Guide Tube, Small I.D. 3 379 Guide Tube, Large I.D. National 4 1571 Gas Hose most models 5 4972 Socket 6 366 Gas Nut 7 4912 Snap Ring 8 4942 Wire Assembly 9 1930 Oetiker Clamp 10 663 Hose Gland 11 7115 Adaptor Body 12 396 Set Screw FOR USE ON ITEM PART NO. DESCRIPTION L-TEC 1 4893 Body, w/Gas Barb & O-Ring mig-31 2 194 Guide Tube, Small I.D. swm-30 3 371 Guide Tube, Large I.D. swm-31 4 1571 Gas Hose 5 4972 Socket 6 1566 Gas Nut 7 4912 Snap Ring 8 4942 Wire Assembly 9 1930 Oetiker Clamp 10 663 Hose Gland 11 4998 Adaptor Body 12 396 Set Screw FOR USE ON ITEM PART NO. DESCRIPTION OTC 1 4893 Body, w/Gas Barb & O-Ring most models 2 4958 Guide Tube, Small I.D. 3 379 Guide Tube, Large I.D. Gelco 4 1571 Gas Hose all models 5 4972 Socket 6 366 Gas Nut 7 4912 Snap Ring 8 4942 Wire Assembly 9 1930 Oetiker Clamp 10 663 Hose Gland 11 7124 Adaptor Body 12 396 Set Screw 13 4261 Spade Terminal FOR USE ON ITEM PART NO. DESCRIPTION Quick Disconnect, 1 4893 Body, w/Gas Barb & O-Ring feeder end w/guide 2 478 Guide Tube, Small I.D. tubes (2) 3 479 Guide Tube, Large I.D. Fits all existing 4 1571 Gas Hose Bernard adaptors 5 4908 Socket 6 1566 Gas Nut 7 4912 Snap Ring 8 4942 Wire Assembly 9 1930 Oetiker Clamp 10 663 Hose Gland FOR USE ON ITEM PART NO. DESCRIPTION ESAB, most models 1 4971 Feeder Mount 2 1456 Hex Nut W/pre-cut guide 3 4974 Hex Jam Nut tubes 4 396 Set Screw 5 3613 Lock Washer 6 4975 Flat Washer 7 4912 Snap Ring 8 B-120 Solder Type Lug 9 4214 Gas Barb Assy. (w/4907 O-Ring) 10 4942 Wire Assembly 11 4973 Button Head Screw 12 4972 Power Socket 13 478 Guide Tube, Small I.D. 14 479 Guide Tube, Large I.D. FOR USE ON ITEM PART NO. DESCRIPTION Universal flange 1 4971 Feeder Mount mount quick 2 1456 Hex Nut disconnect 3 4974 Hex Jam Nut 4 396 Set Screw includes universal 5 3613 Lock Washer centering device for 6 4975 Flat Washer most European 7 4912 Snap Ring feeders 8 B-120 Solder Type Lug 9 4214 Gas Barb Ass...