Login:
Sorted: Name ↑   Downloads   Rate   Size ↓  
downloaded: 13   File size: 4 kb   Manafacture: Amana  
Category: Dryers

downloaded: 11   File size: 4 kb   Manafacture: Amana  
Category: Dryers

downloaded: 13   File size: 4 kb   Manafacture: Amana  
Category: Dryers

downloaded: 13   File size: 4 kb   Manafacture: Amana  
Category: Dryers

downloaded: 16   File size: 129 kb   Manafacture: Amana  
Category: Dryers
@name

2. Install a U.L. approved strain relief into the power cord entry hole of the mounting bracket. Finger tighten the nut only at this time. 3. Thread a U.L. Approved 30 Amp. Power cord, NEMA 10-30 Type SRDT, through the strain relief. 4. Attach the power cord neutral (center wire) conductor to the silver colored center terminal on the terminal block. Tighten the screw securely. 5. Attach the remaining two power cord outer conductors to the outer brass colored terminals on the terminal block. Tigh

downloaded: 18   File size: 156 kb   Manafacture: Amana  
Category: Dryers
@name

After cleaning, put the screen back in place. 3. Empty the condensate collection box During the operation of a program, steam condenses into water is collected in the box. The box must be emptied in time after the program is complete. -Hold the handle of the box and take out the box. When the box is taken out, keep it level to prevent the condensate from overflowing; -Pour away the condensate water. Note: the condensate water can not be used for drink or for food processing; -Put the box back in

downloaded: 13   File size: 182 kb   Manafacture: Amana  
Category: Dryers
@name

The filter is in 3 parts: Exhaust vent shroud, lint filter and exhaust filter (as shown in figure 1). 2. Cleaning the filter Separate the filters from the shroud and remove the lint with a soft brush or vacuum cleaner. Take care not to damage the filters. (See fig 2). Cleaning of the Air Intake Filter The filter should be cleaned once a month. Hold the upper and lower edges of the air intake shroud, push upwards gently with your thumb to disconnect the latch hook then pull outwards to remove. Re

downloaded: 14   File size: 227 kb   Manafacture: Amana  
Category: Dryers
@name

Questions? You'll Need a Few Things Before You Begin See Owner's Manual or call Duct Tape _" Power Cord (3-wire or 4-wire) Amana and Strata Relief Wrench Consumer Screw Drivers Affairs Scrows ggg (supplied) Level Department i .Z <<_ ::_1 i<. _ 1-800-843-0304 Optional Kits REMOVE PARTS Kits are available at extra cost through AND CLEAN your Amana dealer or DRYER DRUM Amana factory 1-800-843-0304. Wipe drum with clean rag and soap Directional Exhaust Kit diluted in warm water to remove any DK1 Sal

downloaded: 19   File size: 227 kb   Manafacture: Amana  
Category: Dryers
@name

Use the foam-removing spin- ning to remove the extra deter- gent liquid. It can both shorten the washing time and save the water consumption. Please put in the gland properly even if the laundries .Do not leave any articles above the depression cover. Push Gland Push Proper The laundries are slanting Proper No gland In spinning, it will pause the work if you open the outer cover of the spintub. Close it to resume the spinning. quantity is small. Maintenance 1 2 Wipe off the water drops on the su

downloaded: 10   File size: 256 kb   Manafacture: Amana  
Category: Dryers
@name

5. Damages to finish after installation. 6. Replacement of light bulbs and/or fluorescent tubes (on models with these features). EXCLUSIONS This warranty does not cover the following: 1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY. Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you. 2. Servic





Category