Votes - 4, Average rating: 4 ( )

Manafacture: GE File size: 452.55 kb File name: 219040en.pdf Language of manual:

0 Press against the filter lid until it clicks into the lock. Cleaning the drum 1 Warning! Do not clean the stainless steel drum with abrasive detergents or steel wool! 0 Wipe the inside of the drum and the drum fins with white vinegar to avoid a build up of residues/deposits effecting the sensors. This is particularly important if you regulary use fabric conditioning sheets or dry starched items in the dryer. Cleaning the panel and operating parts 1 Warning! Do not use household furniture polish or aggressive detergents. 0 Wipe over the panel and operating parts with a damp cloth. Only use warm water. Something not working? Something not working? If the tumble dryer is not working correctly please carry out the following checks before calling an engineer. Symptom Possible cause Solution The tumble dryer will not start The results are unsatisfactory The appliance is not Plug in the appliance plugged in The fuse has blown Check the fuse The START/PAUSE button Press the START/PAUSE has not been pressed button No program has been Select the required selected program The door is not properly Close the door closed The water reservoir is full Empty the water reservoir The wrong program has Select a different been selected program Fluff filter blocked Clean the fluff filter Condenser covered with Clean the condenser fluff Observe the maximum The tumble dryer has loads stated for each been overloaded program Laundry not sufficiently Ensure the wash load is spun prior to tumble well spun before tumble drying drying The vent in the base of Ensure the vent is clear the appliance is covered A residue may have formed on the drum Clean the inside of the interior, blocking the drum with white vinegar sensors Reprogram the standard The conductivity of the The drying result is unsatis setting, eg. H0 instead of water in your locality dif factory; the washing is still H1, for dryer washing (see fers from the standard damp. chapter “Programming setting of the appliance. Possibilities“. Something not working? Symptom Possible cause Solution The drum illumination does not work Is the tumble dryer Plug in the tumble dryer plugged in The program selector is in Turn the program selector the OFF position dial to LIGHT The bulb needs replacing Replace bulb The condenser unit is Clean the condenser unit The drying process takes covered with fluff unusually long Fluff filter is clogged Clean the fluff filter Fluff filter has not been Replace the fluff filter The door cannot be closed inserted correctly and/or and ensure the filter lid is the filter lid not closed closed The door cannot be opened with the DOOR button Electric mains plug not Connect the mains plug connected Set a program. The fill-in door can be opened at Program selector set to any time by pressing OFF firmly against the door (pressing location ) Empty the condensate Display EMPTY WATER is lit Condensate container full container EMPTY WATER indicator illuminated, even though the container has already been emptied The remaining running time display changes rapidly. Foreign bodies, e. g. animal hairs, can block the inlet nozzle as well as the valve on the end of the EMPTY WATER container The remaining running time is adjusted automatically depending on the type of items being washed, the washing time and the degree of dampness. With the container pulled out, switch on the appliance momentarily. The blockage can be removed from the container shaft or the hair cleaned out of the valve Automatic process. There is no unit fault. Something not working? Symptom Possible cause Solution The dryer terminates the drying process automatically: END is displayed shortly after program start; no display of the extent of drying Too dry or too little laundry filled-in for the selected program Select time program or higher drying stage (e.g. EXTRA DRY instead of CUPBOARD DRY) The drying process takes SPECIAL CARE button Check the program selection: SPECIAL CARE unusually long. 4.5 hours after the beginning of the drying process: - END display flashes pressed and too much laundry filled-in button appropriate only for laundry amounts up to 2.5kg - acoustic signal sounds Too much laundry Reduce the amount of - discontinuation of the filled-in laundry filled-in drying process - error code C6 is displayed Laundry too damp Pre-dry the laundry more thoroughly If you do not find the required information in this manual to remedy a disturbance, please call the customer service. Replace the interior light 0 A replacement bulb can be purchased through your local AEG Service Force Centre (Part No: 647072580). 1 Warning! Never use standard light bulbs in your Lavatherm. 0 Isolate the appliance from the mains supply. 0 Screw-off the bulb cover. (The bulb is located at the top behind the door; see Front view). 0 Replace the defective bulb. 0 Screw-on the bulb cover. 1 Warning! For safety reasons the bulb cover must be screwed-on. The dryer must not be operated, without the cover in place. Door Reversal I...

Download now

Please, enter two numbers from picture: