Login:
Votes - 3, Average rating: 3.7 ( )

User manual GE, model SPSD157JMG

Manafacture: GE
File size: 431.62 kb
File name: 492ce2da-afa8-4f04-a502-492a2a60baa5.pdf
Language of manual:enesfr
Free link for this manual available at the bottom of the page



manual abstract


IMPORTANT: Do not lay the washer or dryer on its back! Do not remove the shipping bolts on the back side of the washer. The bolts must remain in place until the washer is returned to an upright position. Use an open-end wrench to remove the washer or dryer leveling legs. B A 1 INSTALLATION PREPARATION Remove the packaging. The Drawer divider is taped at the top of the shipping carton. Remove the divider and set aside for final installation. Flatten the product carton to use as a pad to lay the washer or dryer down on its side. Continue using the carton to protect the finished floor in front of the installation location. Back out and remove all 4 leveling legs Instructions en francais : . . . . . . . . . . . . . . . .4 Instrucciones en espanol: . . . . . . . . . . . . . . .8 Pedestal Models White Pedestal SPSD157JWW Metallic Gold SPSD157JMG Metallic Vermillion SPSD157JMV For Washer Model: WPDH8800 For Dryer Models: DPVH880EJ, DPVH8800GJ BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT — Save these instructions for local inspector’s use. • IMPORTANT — Observe all governing codes and ordinances. • Note to Consumer – Keep these instructions with your Owner’s Manual for future reference. • Completion time – 1 to 2 hours • Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under the Warranty. CAUTION — Due to the size and weight of these products, and to reduce the risk of personal injury or damage to the product, TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION. • See washer and dryer installation instructions for additional installation requirements and guidelines. 2 Installation Instructions INSTALL THE PEDESTAL TO THE WASHER OR DRYER Place the pedestal against the bottom of the unit. Check to be sure the drawer front is at the front of the unit. Align the holes in the pedestal with the holes in the bottom of the unit. Use a Phillips screwdriver to install the 4 screws through the pedestal and into the unit—do not tighten. Slide the pedestal toward the unit, until it is aligned front to back. Use an 8 mm socket wrench to securely tighten the screws. C B A PREPARE THE PEDESTAL 3 Pull the drawer out as far as it will go. Remove screws from drawer slides. Slide drawer out of the base and set aside. FOR DRYERS ONLY: Locate the 4 support pads from the parts package. Each pad has 2 protrusions that fit into the holes on top of the pedestal. Press the rubber pads into each set of corner holes on the top of the pedestal as shown. NOTE: The support pads should be installed on the dryer only. DO NOT INSTALL THESE PADS ON THE WASHER PEDESTAL. C B A 2 Installation Instructions LEVEL THE WASHER OR DRYER Locate the 4 legs from the parts package and install. Stand the washer or dryer upright. Move it close to its final location. Make sure that the washer or dryer is level by placing a spirit level on top. Check side to side and front to back. Use an open ended wrenc...

Other models in this manual:
Dryers - DPVH8800GJ (431.62 kb)
Dryers - SPSD157JMV (431.62 kb)
Dryers - SPSD157JWW (431.62 kb)
Dryers - WPDH8800 (431.62 kb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category