Votes - 0, Average rating: 5
(
)
)
|
manual abstract
43 kg max. 8 kg 230 V 16 A 2350 W B 4.48 kWh 282 kWh Domestic + 5°C to + 35°C Consumption values The consumption values have been established under standard conditions. They may deviate when the machine is operated in domestic circumstances. Katoen Kast droog (COTTON CUP- BOARD)2) 3) Katoen Strijkdroog (COTTON IRON)2) Synthetisch Kast droog (SYNTHETICS CUP- BOARD)2) Energy consumption in kWh / average Programme drying time in min. 4.48 / 135 (8 kg load pre-drained at 1000 rpm) 4,30 (8 kg load pre-drained at 1400 rpm) 3.8 / 108 (8 kg load pre-drained at 1000 rpm) 1.30 / 45 (3 kg load pre-drained at 1200 rpm) 1) Different loading volume data may be needed in some countries as a result of different measuring methods. 2) in accordance with EN 61121 Machine settings Setting Implementation Zoemer (BUZZER ) permanent off 1. Turn the programme selector to any programme. 2. Press simultaneously the Zoemer and Droogtegraad buttons and hold down for approx. 5 seconds. 3. The buzzer is by default always off. You can use Zoemer button to activate or deactivate sound but machine does not memorize your selection. 16 electrolux Water hardness Water contains, a variable quantity of limestone and mineral salts of which quantities vary according to geographical locations thus varying its conductivity values. Relevant variations of the conductivity of the water compared to those prefixed by the factory could slightly influence the residual humidity of the laundry at the end of the cycle. Your dryer allows you to regulate the sensitivity of the drying sensor based on conductivity values of the water. Hints for test institutes 1. Turn the programme selector to any programme. 2. Press simultaneously the Droogtegraad and START/PAUZE buttons and hold down for approx. 5 seconds. The current setting is on the display: – low conductivity <300 micro S/cm – medium conductivity 300-600 micro S/cm – high conductivity >600 micro S/cm 3. Press the START/PAUZE START PAUZE button sequentially until you set desired level. 4. To memorize setting press simultaneously the the Droogtegraad and START/PAUZE buttons or turn knob to O off position Parameters possible to checked by the Test Institutes: • Energy consumption (corrected with final humidity) during the cupboard dry cotton cycle with nominal load. • Energy consumption (corrected with final humidity) during the cupboard dry cotton cycle with half load. • Final humidity (during cupboard dry cotton, iron dry cotton and cupboard dry easy care) Installation • Condensation efficiency (corrected with final humidity) during cupboard dry cotton cycle with nominal and half load All the cycles have to be checked in accordance with EN 61121 (Tumble dryers for household use – Methods for measuring the performance). Important! The appliance must be moved in vertical position for transport. Appliance positioning • It is recommended that, for your convenience, the machine is positioned close to your washing machine. • The tumble dryer must be installed in a clean place, where dirt does not build up. • Air must be able to circulate freely all round the appliance. Do not obstruct the front ventilation grille or the air intake grilles at the back of the machine. • To keep vibration and noise to a minimum when the dryer is in use, it should be placed on a firm, level surface. • Once in its permanent operating position, check that the dryer is absolutely level with the aid of a spirit level. If it is not, raise or lower the feet until it is. • The feet must never be removed. Do not restrict the floor clearance through deep- pile carpets, strips of wood or similar. This might cause heat built-up which would interfere with the operation of the appliance. Important! The hot air emitted by the tumble dryer can reach temperatures of up to 60°C. The appliance must therefore not be installed on floors which are not resistant to high temperatures. When operating the tumble dryer, the room temperature must not be lower than +5°C and higher than +35°C, as it may affect the performance of the appliance. Important! Should the appliance be moved, it must be transported vertically. Important! The appliance must not be installed behind the lockable door, a sliding door a door with a hinge on the opposite side to that of the appliance. Removing transport safety packaging Caution! Before use all parts of the transport packaging must be removed. 1. Open loading door 2. Pull off adhesive strips from inside machine on top of drum. 3. Remove foil hose and polystyrene padding from the machine. Electrical connection Details on mains voltage, type of current and the fuses required should be taken from the type plate. The type plate is fitted near the loading aperture (see “Product description” chapter). Service electrolux 17 Warning! The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precautions. Should the appliance power supply cable need to be replaced, this must be car...