Votes - 3, Average rating: 4
(
)
)
|
manual abstract
men time is up, check and redistribute mattress pads.) load. Reset timer and check at 5 minute intervals. Check after each 5 minutes to ensure articles do not fill dryer drum. Large, wet articles should have ample room in the dryer, but as they dry and fluff up they may not have room to tumble. CAUTION: Items without room to tumble may block airflow and could result in scorched items. Dry matwess pads separately. Use a low heat drying setting. Loading As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Sort by color (Separate colorfast from non-colorfast fabrics*) l Whites l Lights l Darks Separate by fabric type . Cottons and linens l Permanent press cottons and blends . Synthetic and poly knits l Delicates Separate lint producers from lint collectors l Lint producers: terry cloth and chenille l Lint collectors: velveteen and corduroy Sort by weight . Heavy Items l Light Items * Non-cohrfatfah~ may bhed wfah, Soti @ individual COIW. l Avoid drying veq small loads. . Do not dry the following items: . Sort clothes by weight so you . Fiberglass items won’t have to run an extra cycle l Woolens for one or two heavier, slower . Rubber coated items drying items. l Plastics . Do not add fabric softener sheets . Items with plastic trim once the load has become warm. . Foam-filled items This may cause fabric softener stains. . Do not overload. This causes inefficient operation and unnecessary wrinkling. Clothes need to tumble freely. The drum is rust-resistant and requires no special care. Wipe off any spills or washing Apply these pretreatment products compounds. Wipe or dust with away from the dryer. The fabric a damp cloth. Try not to strike may then be washed and dried the surface with sharp objects. normally. Damage to your dryer Dryer control panel and finishes caused by pretreatment products may be damaged by some laundry is not covered by your warranty. pretreatment soil and stain remover products if such products are sprayed on or have direct contact with the dryer. Before every dryer use, clean the lint filter. Moisten your fingers and reach into the filter opening. Run b # your fingers across the filter. B /-’ /- To keep your dryer operating at peak performance, be sure to have a technician vacuum the lint from the machine every three years. To store your dryer for a short period of time, disconnect the power supply and clean the lint filter. Care @ Cleaning Inspect and clean the dryer exhaust ducting at least once a year to prevent clogging. A partially clogged exhaust can lengthen the d~ing time. To clean the exhaust duct follow these steps: 1 Turn off electrical supply by disconnecting the plug from the wall socket. 2 Disconnect exhaust duct from the dryer. 3 Vacuum the exhaust duct with the hose attachment. 4 Reconnect the exhaust duct to the dryer. l Make sure the inside flaps of the exhaust hood move freely (you may want to check with a mirror). l Make sure inside flaps are fully open when dryer is operating. l Make sure there is not wild life (birds, insects, etc.) nesting inside the exhaust duct or hood. Check the inside of the exhaust hood with a mirror to rid of debris Problem Possible Causes What to Do Dryer is unplugged l Make sure the dryer plug is pushed completely into the outlet. Fuse is blown/circuit l Check the house fuse/circuit breaker breaker is tripped box and replace fuse or reset breaker. NOTE.Most electric dryers use two breakers. Fuse is blown/circuit breaker l Check the house fuse/circuit breaker box is tripped, the dryer may and replace fuse or reset breaker. tumble but not heat Gas service is off l Make sure gas shutoff at dryer and main shutoff are fully open. ,“” ” Some shaking/noise is normal. l Move dryer to an even floor space, or adjust Dryer may be sitting unewdy as necessary until even. tiproper use of fabric softener l Follow directions on fabric softener package. Drying dirty items with c Use your dryer to dry only clean items. Dirty clean ones items can stain clean items and the dryer. ~othes were not completely l Sometimes stains which cannot be seen when clean the clothes are wet “appear” after drying. Use proper washing procedures before drying. tit falter is fti l Clean lint screen before each load. hproper sorting l Sort lint producers (like chenille) from lint collectors (like corduroy). Static electricity can attract tit l See suggestions in this section under STATIC. krloading l Separate large loads into smaller ones. Paper, tissue, etc. left in pockets . Empty all pockets before laundering clothes. Problem Possible Causes What to Do “Try a fabric softener. l Adjust controls for less drying. No fabric softener was used l TV a fabric softener. Synthetics, permanent press “Try a fabric softener. and blends can cause stitic hproper sorting l Separate heavy items from lightweight items (generally, a well-sorted washer load is a well-sorted dryer load). Large loads of heavy items (We beach toweb) l Large, heav...
Other models in this manual:Dryers - DBLR453GT (789.71 kb)