Votes - , Average rating: ( )

User manual ADC, model 600

Manafacture: ADC
File size: 461.32 kb
File name: 52ad222d-0c3f-4b26-830d-9df47a396a4e.pdf

Language of manual:

The document is loading, please wait

Download nowClose

The document is loading, please wait

Download nowClose

• The programme selector knob may be turned in either direction to select the required programme. • Always choose a programme which is suitable for the fabric type and observe the symbols on garment care labels. • With a little practice you will soon determine which programme suits your requirements. Anti Crease • The laundry may be removed after a drying cycle has been completed. • Alternatively, the laundry may be left in the drum, in which case the machine will automatically perform an Anti Creasing phase. • Throughout this phase he laundry is separated , smoothed and cooled. The Anti creasing indicator will flash and the drum will rotate briefly every 60 seconds for about 2 hours. Buzzer • At the end of a drying programme and throughout the Anti creasing phase, a buzzer (Chime on certain models) will sound. • If this is annoying, the buzzer may be muted by pressing the Buzzer Cancel button. Control panel lock • To prevent accidental operation of the dryer, the controls may be locked. • Press the Buzzer Cancel and the Start/Pause/ Cancel buttons simultaneously and hold down for 3 seconds. (To unlock, repeat the procedure). • One of the progress indicators will flash. • When the dryer is in locked mode, only the ON/OFF button will function. • The lock may be activated during operation or in standby mode. Programme progress indicators This vertical row of indicators show which phase of the drying cycle is operational. Drying Ready to iron Ready to wear End -Anti crease The door • Open the door by pulling on the handle • Opening the door will automatically stop the dryer operation. • To close the door , push until a click is heard. • If required, the door hinging may be reversed so that the door opens from right to left. • Note . Activating the control panel lock, does not lock the door. Lint filter It is essential that the lint filter be cleaned after every drying cycle At the end of a programme the indicator will glow as a reminder to clean the filter. Pull the lint filter out and open it Unfold the filter and carefully remove the accumulated lint using a soft cloth. Fold, close and return the filter to its housing. Drum ribs Humidity sensors are located on the inside of the drum ribs. These determine when the laundry is dry. The ribs should be cleaned every three months. Wait till the dryer has cooled down and wipe the ribs with a soft cloth dipped in vinegar, then wipe dry. Page 5 Trouble shooting 7 Trouble shooting 7 Since the following are not factory faults, they are the owner’s responsibility. • Damage to exterior finish. • Breakage of components • Damage through improper use or installation of the dryer. • Damage caused by moving the dryer. Problem –Check The dryer or a programme will not start. Has the ON/Off button been pressed? Has a programme been selected? Has the Start/Pause /Cancel button been pressed? Has the power cable been plugged in? Has a house circuit breaker tripped? The ‘End-Anti crease’ indicator flashes for up to two hours. This is normal. The anti crease stage can last up to two hours. If you wish to reduce the time, switch the dryer off and remove the laundry. The buttons on the control panel do not respond to pressing. Check that ‘Control panel lock’ has not been activated. If the fault persists, unplug the dryer, wait a few minutes and try again. The ‘Drying’ indicator flashes. Press the ON/Off button to switch the dryer off and call service for assistance. The programme stops for no apparent reason. Is the door open? Has the power supply been interrupted? Press the ‘Start/Pause/Cancel’ button. The laundry is too moist or the drying time is too long or the Clean filter indicator flashes. Has the drum been overloaded? Check that the ventilation slots are free of obstructions. Check for blockages in the vent tube. Clean the ‘Fluff filter.’ Confirm that the correct programme was used. Textiles have shrunk or have been damaged Only dry textiles labelled safe for tumble drying. Choose a suitable programme for the fabric type. If you experience a problem with the machine, please check the following before calling a Service technician. It may seem obvious …..but you may be charged for a service call, even during the warranty period, if no fault is found. 1. Check that the cord is plugged in and that the wall socket switch is on. 2. Check that there is power to the wall socket by testing the socket with a small electric appliance such as a kettle or hair dryer. 3. Check if a house circuit breaker has tripped out. 4. Check that the laundry is evenly distributed inside the drum. 5. Check that the machine is not over loaded. 6. Check that the dryer door is firmly closed. 7. Check that the ON / OFF button is pushed in. 8. Check that the fluff filter has been cleaned. Page 6 8 Technical specifications Drying method Vented, electronic sensor controlled Height (Highlight) 850mm Width 595mm Depth 540mm Height adjustment of feet 5mm Weight, unpacked 29kg approx. Service Centres If you have fol...