Votes - 5, Average rating: 4.2 ( )

Manafacture: Frigidaire File size: 1.71 mb File name: 7702a31b-bdcc-47c9-96c7-cd7b3098da52.pdf Language of manual:

8. Replace heat exchanger and lock into place (turn both lock washers outwards until they snap into place). 9. Close door in plinth. CAUTION! Never operate the dryer without the heat exchanger. Cleaning the drum CAUTION! Do not use abrasives or steel wool to clean the drum. Lime in the water or cleaning agents may form a barely visible lining on the inside of the drum. The degree to which the laundry has been dried is then no longer detected reliably. The laundry is damper than expected when removed from the dryer. Use a standard domestic cleaner (e.g. vinegar-based cleaner) to wipe down the inside of the drum and drum ribs. Clean operating screen and housing CAUTION! Do not use furniture cleaners or aggressive cleaning agents to clean the machine. Use a damp cloth to wipe down the operating screen and housing. Care and cleaning 19 20 20 What to do if ... What to do if ... Troubleshooting by yourself If, during operation, the error code E... plus number or letter) appears on the LCD: Switch the machine off and on again. Reset programme. Press the START PAUSE button If the error is still displayed, please inform your local Service Force Centre and quote the error code. Problem Possible cause Remedy Dryer does not work. Mains plug is not plugged in or fuse is not working correctly. Plug in at mains socket. Check fuse in fuse box (domestic in- stallation). Loading door is open. Close loading door. Have you pressed the START PAUSE button? Press the START PAUSE button again. Drying results unsatisfactory. Wrong programme selected. Select a different programme the next time you dry (see “Pro- gramme chart” chapter). Lint filters clogged. Clean lint filters. Fluff filter clogged. Clean fluff filter. Heat exchanger clogged with lint. Clean heat exchanger. Overloading of laundry. Observe recommended loading volumes. Ventilation slots in base area covered up. Uncover ventilation slots in base area. Residue on inside surface of drum or drum ribs. Clean inside surface of drum and drum ribs. Conductance of water at in- stallation site differs from standard setting of machine. Re-programme standard set- ting for degree of drying (see ‘Programming options’ chap- ter). Loading door does not close. Fine strainer not in place and/ or mesh filter not locked in place. Install fine strainer and/or snap large mesh filter into place. When a button is pressed, Err appears on the LCD. Washing protection. After the start of the programme, the option can no longer be set. Turn the programme knob to OFF. Set the programme again. Drum light does not work. Programme selector in OFF po- sition. Turn programme selector to DRUM LIGHT or to any pro- gramme. Defective light bulb. Replace light bulb (see next section). What to do if ... 21 Displayed programme time changes erratically or stays un- changed for a long time. Programme time is corrected automatically depending on type and volume of laundry and level of dampness. Automatic process; this is not a machine fault. Programme inactive, empty water tank warning led is light- ing. Condensate tank is full. Empty condensate tank, then start programme with START PAUSE button. Drying cycle ends shortly after programme starts. Not enough washing loaded or washing loaded is too dry for selected programme. Select time programme or higher drying level (e.g. EXTRA DRY instead of STORAGE DRY). Drying cycle lasts an unusually long time. Note: After around 5 hours the drying cycle ends au- tomatically (see „Drying cycle complete ”). Lint filter clogged. Clean lint filter. Fluff filter clogged. Clean fluff filter. Load volume too big. Reduce load volume. Laundry insufficiently spun. Laundry must be adequately spun. Particularly high room temper- ature. Temporary switching off of the compressor to avoid overload. Automatic process, there is no fault with the appliance. If pos- sible, lower the room tempera- ture. Changing the bulb for interior lighting Only use a special bulb which is designed specially for dryers. The special bulb can be obtained from your local service centre. When the appliance is switched on, the interior lighting switches itself off after 4 minutes when the door is open. WARNING! Do not use standard bulbs! These develop too much heat and may damage the machine! Before replacing the bulb, disconnect the mains plug; with a permanent connection: fully unscrew or deactivate the fuse. 1. Unscrew cover above the bulb (this can be found directly behind the loading aperture, at the top; refer to “Description of machine” section.) 2. Replace defective bulb. 3. Screw cover back down. Check the correct positioning of o-ring gasket before screwing back the door light cover. Do not operate the dryer when missing o-ring gasket on door light cover. WARNING! For safety reasons, the cover must be screwed down tightly. If this is not done, the dryer must not be operated. 22 22 Machine settings Machine settings Setting Implementation BUZZER permanent off 1. Turn the programme selector to any programm...

Download now

Please, enter two numbers from picture: