Votes - 2, Average rating: 4.5 ( )

Manafacture: Frigidaire File size: 825.73 kb File name: 944726en.pdf Language of manual:

If the condensate tank is full, an active programme will break off automatically and the EMPTY WATER (RESERVOIR) display will light up. In order to continue the programme, the condensate tank must first be emptied. 1 Warning! The condensate is not suitable for drinking or for preparing foodstuffs. 1.Take out drawer containing condensed water container completely (1) and pull up the condensed water container’s drainage pipe as far as it will go (2). 2.Pour condensed water out into a basin or similar receptacle. 3.Slide outlet connections in and re fit condensate tank. If the programme has been interrupted as a result of the condensate tank being full: Press the START/PAUSE (START/ PAUZE) button to continue the drying cycle. 3 The condensate tank has a volume of approx. 4 litres. This is sufficient for around 6kg of laundry which has previously been spun at 800 revolutions/ minute. 3 The condensate can be used as distilled water, e.g. for steam ironing. However first filter the condensate (e.g. with a coffee filter) to remove any residue and small pieces of fluff. Cleaning the fluff filter If the indicator CLEAN BASE FILTER (REINIG SOKKELFILTER) lights up, the fluff filter and the filter mat in the base of the appliance must be cleaned. 3 To protect the heat pump from dirt, the dryer is fitted with a special filter mat, which is located in the filter housing. Here too large amounts of fluff build up over time, which affect the function of the appliance. 1 Important • Operating when the fluff filter is clogged with fluff can damage the dryer. This also increases energy consumption. • Never operate the dryer without the fluff filters. • Do not use the dryer without the filter mat. A dirty heat pump requires more energy and can only be cleaned up by means of a costly process. 1.Open door. 2.Open door in plinth: To do this, press the release button on the bottom of the door aperture and open the door in the plinth to the left. 3.Pull filter housing out of the base by the handle. 4.Clean the inside of the door, the fluff filter chamber and the rubber seals of fluff. 5.Remove fluff from the fluff filter on the floor of the base with a damp hand. 6.To clean the filter mat: Remove filter mat from filter housing. To do this, press the pressure points on the sides and pull the filter mat and frame up and out of the housing. 7.Take the filter mat out of the frame and wash it by hand or use a vacuum cleaner, when it is has dried out. Fluff, which has become stuck in the filter mat and has not been removed by washing, does not affect the function. 8.Insert the filter mat in the frame and then insert with the frame into the filter housing. 1 Important: The filter mat must engage tightly with the frame. Check that the mat is sitting snuggly in the frame, especially after inserting it into the filter housing. 9.As necessary, approx. once every 6 months, remove the fluff from the heat exchanger using the sponge supplied. When doing this, please use rubber gloves. Tip: The fluff can be removed more easily if it is first dampened e. g. with a laundry dampener. 10. Re-insert filter housing with frame and filter mat in the base of the appliance. Note: If the filter mat and frame are not inserted in the filter housing, the filter housing cannot be pushed into the base of the appliance. 11. Close door in plinth. 3 The indicator CLEAN BASE FILTER (REINIG SOKKELFILTER) only goes out when the programme knob has been positioned to OFF (UIT). Cleaning the drum 1 Caution! Do not use abrasives or steel wool to clean the drum. 3 Lime in the water or cleaning agents may form a barely visible lining on the inside of the drum. The degree to which the laundry has been dried is then no longer detected reliably. The laundry is damper than expected when removed from the dryer. Use a standard domestic cleaner (e.g. vinegar-based cleaner) to wipe down the inside of the drum and drum ribs. Clean operating screen and housing 1 Caution! Do not use furniture cleaners or aggressive cleaning agents to clean the machine. Use a damp cloth to wipe down the operating screen and housing. What to do if … Troubleshooting by yourself If, during operation, the error code (E plus number or letter) appears on the multi-display: Switch the machine off and on again. Reset programme. Press the START/PAUSE (START/PAUZE) button If the error is still displayed, please inform your local Service Force Centre and quote the error code. Problem Possible cause Remedy Mains plug is not plugged in Plug in at mains socket. Check or fuse is not working corfuse in fuse box (domestic inrectly. stallation). Dryer does not work. Loading door is open. Close loading door. Have you pressed the START/ Press the START/PAUSE (START/ PAUSE (START/PAUZE) but- PAUZE) button again. ton? Problem Possible cause Remedy Drying results unsatisfactory. Select a different programme the next time you dry (see Wrong programme selected. “Overview of programmes” section). Lint filters clogged. Clean lint ...

Download now

Please, enter two numbers from picture: