Votes - 2, Average rating: 4 ( )

Manafacture: Frigidaire File size: 359.64 kb File name: a6cf043f-eeaa-4f84-8723-40b7577c71c5.pdf Language of manual:

Correct Incorrect Correct Incorrect Correct Incorrect Electrical Connections Requirements and Instructions 1. This appliance must be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. 2. Do not use an extension cord with this dryer. Some extension cords are not designed to withstand the amounts of electrical current this dryer utilizes and can melt, creating electric shock and/or fire hazard. Locate the dryer within reach of the receptacle for the length of power cable to be purchased, allowing some slack in the cord. Refer to the electrical requirements in this manual for the proper power cord to be purchased. 3. A approve strain relief must be installed onto power cable. If the the strain relief is not attached, the cord can be pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock. 4. Do not use an aluminum wire receptacle with copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and aluminum and can cause electrical shorts. The proper wiring and receptacle is a copper wired power cord with a copper wired receptacle. Danger: Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded. 3-Wire Cord Connections nut tighten nut to these threads power cord Strain relief mounting bracket G N L 1. Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer in the upper corner. 2. Install a strain relief into the power cord entry hole of the mounting bracket. Finger tighten the nut only at this time. 3. Thread a 30 Amp. Power cord, 245 IEC66(YCW) 450V/750V, through the strain relief. 4. Attach the power cable earthconductor to the silver coloured centre terminal on the terminal block. Tighten the screw securely. 5. Attach the remaining two power cable outer conductors to the outer silver coloured terminals on the terminal block. Tighten both screws securely. Warning:Do not make a sharp bend or crimp wiring/conductor at connections. 6. Reattach the strain relief mounting bracket to the back of the dryer with two screws. Tighten screws securely. 7. Tighten the screws securing the cable restraint firmly against the power cable. 8. Tighten the tension relief nut securely so that the tension relief does not turn. 9. Reinstall the terminal block cover. Grounding instruction: This appliances must be connected to a ground metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. 22 WARNING-improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the appliance is properly grounded. Caution: Label all wires prior to disconnection, when servicing controls. Wiring errors can cause improper operation and be dangerous. Check unit for proper operation after servicing. Warning: Discard or destroy the carton and plastic bags after the dryer is unpacked. Children should not be allowed to use them to play with. Cartons covered with rugs, bedspreads, or plastic sheets can become an airtight chamber and cause suffocation leading to death. Make all packing materials inaccessible to children. Warning: The instructions in this manual and all other literature included with this dryer can not cover every possible condition and situation that may occur. Good safety practice and caution must be applied when installing, operating and maintaining any appliances. After installing, if you are in doubt, call a qualified electrician to install and wire the dryer. Specifications Model GDZ22-2 Rated voltage , frequency 220V~ 50Hz Rated dry capacity 10 kg Rated dry power 4800W Weight (about) 55 kg Dimension L712mm W686mm H1115mm ...

Download now

Please, enter two numbers from picture: