Votes - 1, Average rating: 4
(
)
)
|
manual abstract
The machine may also overheat: this will cause it to stop automatically. Clean the filter as follows: © Grasp the filter holder by the two holes near the center and pull it off the peg on which it is supported in the front door. Take the filter out of the holder and brush away the lint in it by hand. NOTE: Wear and tear of fabrics in a tumble dryer is insignificant. The lint caught in the lint filter is dust and fiber residue that has been formed when the garments have been used. Replace the filter in the holder and refit the holder in position on the peg in the door. Note! Clean lint collecting near the tumble dryer as it can be sucked into the air intake. Other user service About once a year, remove the flexible exhaust air hose and clean it and the outlet from the machina 5 How the dryer works © Air is drawn in from the room through the bottom of the machine. © An electric heater heats the air passing into the drum. (D Warm air enters the drum through holes in the back and dries the washing. The drum rotates, and the two paddles prevent garments from becoming tangled. © The air passes through the lint filter at the front of the drum and enters the fan. Air is forced out through the outlet you have selected through a fixed duct (see page 11). The temperature remains at approximately 40°C (104°F) as long as the clothes are moist. When the clothes dry, the temperature rises and the heater element is automatically switched off at the preset temperature. The air that is not heated is then drawn through the drum and cools the clothes for about 15 minutes. The thermostats which switch off the heating at normal and low temperature (60°C (140°F) 45°C (113°F)) are fitted next to the fan. There are also two thermostats next to the heater element. One switches off the heater element if the temperature becomes too high and the other switches off the complete tumble dryer if a fault occurs. This overheating protection, which is fitted at the rear of the machine, can be reset when the temperature has fallen. Refer to the section entitled "If the machine does not work" (pg. 5). Safety The dryer must not be used to dry fabrics which may contain residues of flammable liquids. The dryer door has a magnetic lock, which means that it can be opened from the inside. A door switch automatically stops the dryer if the door is opened. The machine does not start automatically if the door is closed, i.e. if a child should get into the drum and close the door from the inside. In order to restart the machine, the Start pushbutton must be pressed. The machine is protected by a thermostat fitted by the heating element, which turns the machine off if the temperature is too high. Energy saving hints • Dry consecutive loads to avoid reheating the dryer. • Do not overload the dryer. • Do not put unspun, very wet items in the dryer. • Clean the lint filter after each load. • Do not over dry clothes when using the timed program. • If you plan on ironing items, remove them while still slightly damp. • Leave the door closed while the dryer is in operation. 6 Electrical Installation Electrical installation must be carried out by a skilled electrician. As supplied, the machine is arranged for single-phase. Connection as delivered: 1-phase, 208/230 V, heater power 2850 W, 15 A fuse required. NOTE: Follow all state and local codes. To install washer/dryer into a single 30A 208/24OV wall receptical: 1. Remove top of washer - by removing three 25 torx screws. 2. Using power cord attached to dryer, thread through power cord restraint on washer. Attach to terminal block on bulk Head. NOTE: This should be at the top of the terminal block. 3. Remove knock-out plug on bulk head of washer. Install dryer cord 30A 250V AWG 10/3 through knock-out to terminal block. 4. Replace top to washer and test units. Specifications Height 32 1/4" (820 mm) Width 23 1/2" (595 mm) plus exhaust connection Depth 23 1/2” (595 mm), including control panel and program knob Weight 86 lbs. (39 kg) Drum volume 29.3 gallons (111 1) Speed 52 rpm Power 2200/3150 W requirement For connection Single-phase, 15 A as supplied Heater power Single-phase, 2850 W Air flow 196-222 cubic yds./hr. (150-170 m3/h) Drum material Stainless steel Outer casting Galvanized steel sheet Installation Free-standing, built-in or on top of a washing machine Connection to a ventilation duct Connect the exhaust hose from the tumble dryer to a ventilation exhaust fitting or to a discharge through the wall. Secure the hose joint to the outlet stub on the machine. Run the hose, with as few bends as possible to the point of discharge. If necessary, it can be extended to a maximum of 8.75 yards of 4" diameter hose. Make any bends as gentle as possible. A maximum of four 90° bends may be fitted in the hose. The more bends and the longer the hose, the less will be the amount of air passing through the machine. If more than 8.75 yards of hose is n...