Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
Timer follow-up indicator One of the LED lights will remain on as far as programme runs and shows the approximate remaining time. CLEDs on the timer follow-up indicator will also flash when the child-proof lock is activated. Changing the programme after the programme has started You can use this feature to dry your laundry in a different programme after your machine has started to run. For example; Press and hold the “Start/Pause/Cancel” button for about 3 seconds to select “80” minutes programme instead of “60” minutes programme Select the “80” minutes programme by rotating the programme knob. Press “Start/Pause/Cancel” button to start the programme. C The programme which is selected first will go on even if the programme selection button is moved and another programme mode is selected while the machine is operating. You must cancel the ongoing programme in order to change the drying programme. (See, Ending the program through cancelling) Adding/removing laundry in standby mode In order to add or take out laundry after the start-up of the programme 1. Press the “Start/Pause/Cancel” button to switch the machine to “Pause” mode. Drying process will stop. 2. Open the door at Pause position and close it again after adding or taking out laundry. 3. Press “Start/Pause/Cancel” button to start the programme. C Any laundry added after the drying process was started may cause the already dried clothes in the machine intermingle with wet clothes and the result will be wet laundry after the drying process is over. C Laundry may be added or taken out as much as desired during a drying process, but as this process will interrupt drying continuously, it will extend the programme duration and increase energy consumption. Therefore, it is recommended to add laundry before the drying programme is started. Child-proof lock There is a childproof lock to prevent any programme interruption due to the pressing of keys while the programme is on. The loading door and all keys except the “On/Off” key on the panel are deactivated when the child-proof lock is active. In order to activate the childproof lock, press the “Start/Pause/Cancel” and “Low temperature” buttons simultaneously for 3 seconds.To start a new programme after the programme is over or to interrupt the programme, the childproof lock should be deactivated. To deactivate the childproof lock, press the same buttons for 3 sec. C One of the LEDs on the programme follow-up indicator starts flashing when the child-proof lock is activated. CChild-proof lock is deactivated when the machine is restarted by pressing the On/Off button. Ending the programme through cancelling The programme which is selected first will keep on going even if the position of the programme selection button is changed. A new programme can be selected and started after “Programme cancel” is activated in order to change the drying programme. To cancel any selected programme; • Press “Start/Pause/Cancel” button for about a duration of 3 seconds. The “Filter cleaning” warning LED as well as the “0” warning LED on the programme follow-up indicator will light up at the end of this period for reminding purposes. A As the inside of the machine will be excessively hot when you cancel the programme while the machine is running, activate the freshen up programme to cool it down. End of programme The “Filter cleaning” warning LEDsas well as the “0” warning LED on the programme follow-up indicator will light up at the end of the programme. The door can be opened and the machine becomes ready for a second cycle. Press the “On/Off” button to shut down the machine. C A 2-hour anti creasing programme to prevent laundry from creasing will be activated if you do not take the laundry out after the programme has come to an end. C Clean the filter after each drying (please see, Filter cleaning). 7 7 Quick instructions for daily use Preparation and starting 1. Press the “On/Off” button. 2. Place the laundry in the machine. 3. Select the programme. 4. Close the loading door. 5. Press “Start/Pause/Cancel” button. Cancelling a programme A new programme can be selected and started after “Programme cancel” is activated in order to change the drying programme. In order to cancel the selected programme, press “Start/Pause/Cancel” button for about 3 seconds. The “Filter cleaning and “0/ Anti-creasing” warning LEDs will light up at the end of this period for reminding purposes. Adding laundry In order to add laundry after the start-up of the programme: 1. Press “Start/Pause/Cancel” button. 2. Open the loading door and put the laundry in. 3. Close the loading door. 4. Press “Start/Pause/Cancel” button to start the programme. Changing the programme after the programme has started You can use this feature after your machine has started to dry your clothes under higher or lower temperatures. Press and hold the “Start/Pause/Cancel” button for about 3 seconds to switch the machine into the “Cancel” status in order to change the programme. ...