Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
Hint: The #10 x 2,2 cm black screws may have been assembled to the screw retainers. Seat Height Adjusters Position 4 Press Lever • While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown. 8 Seat Assembly SocketsSockets esSeat Bottom Tubes 9 • Fit the seat assembly between the frames. • Insert the seat bottom tubes into the sockets in each seat height adjuster. Hints: • Be sure the seat height adjusters are in the same position (position 4). • You may need to push the frames apart slightly to fit the seat bottom tubes into the seat height adjuster sockets. 6 7 PUSH Seat Bottom Tube Ends PUSH Base • Fit the frame front legs onto the remaining base. • Fit a screw retainer over a hole in the front leg. • Insert a #10 x 2,2 cm black screw through the screw retainer and front leg. Tighten the screw. • Repeat this procedure to secure the other end of the base with the remaining screw retainer and #10 x 2,2 cm black screw. Hint: The #10 x 2,2 cm black screws may have been assembled to the screw retainers. Screw Retainers Assembly 10 • Push each seat height adjuster to be sure they are completely on the seat bottom tubes. • Insert a #8 x 1,9 cm screw through each seat height adjuster and the ends of the seat bottom tube. Tighten the screws. This may require extra force. 11 Seat Height Adjuster • Push each seat height adjuster to be sure they are completely on the seat bottom tubes. • Insert a #8 x 1,9 cm screw through each seat height adjuster and the ends of the seat bottom tube. Tighten the screws. This may require extra force. Seat Bottom Tube Ends 12 Assembly Tabs Pad Elastic Loops Elastic Loops 13 • Insert the crotch belt through the slot in the pad. Make sure the crotch belt is not twisted. Slot Crotch Belt 14 BACK AND BOTTOM VIEW FRONT VIEW Hole Hole • Lift the bottom of the pad. Insert the two elastic loops on the pad through the holes in the seat bottom. • From the back and bottom of the seat, hook the elastic loops to the tabs on the seat. 8 9 Bottom Slots • Lift the top of the pad. • Thread the waist/shoulder belts through the bottom slots in the back of the seat pad. Shoulder Portion • Fold the top of the pad down. • Remove the shoulder portion of the waist/shoulder belts by feeding them through the slots in the seat back. 15 16 Assembly • Insert the shoulder portion of the shoulder/waist belt through the slots in the pad and seat back. - Use the lower shoulder belt slots for a smaller baby. - Use the upper shoulder belt slots for a larger baby. • Fit the top of the pad over the seat back. • Fold the bottom edge of the pad under the edge of the seat bottom to fasten. Upper Shoulder Belt Slots Shoulder Portion Lower Shoulder Belt Slots Belt Ends • From behind the seat, be sure the shoulder portion of the waist/ shoulder belts are secure in the seat back slots. 17 18 10 Prevent serious injury or death from falls or sliding out: • The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. • Do not use the high chair unless all components are correctly fitted and adjusted. • Place your child in the seat. Position the crotch belt between your child’s legs. • Fasten both waist/shoulder belts to each side of the crotch belt. Make sure you hear a "click" on both sides. • Check to be sure the restraint system is securely attached by pulling it away from your child. The restraint system should remain attached. Waist/Shoulder Belt Waist/Shoulder Belt Crotch Belt Secure Child 1 WARNING • Tighten each waist belt and shoulder belt so that the restraint system is snug against your child. Please refer to the next section for instructions to tighten the waist belts. 2 TIGHTEN LOOSEN To tighten the waist belts: • Feed the anchored end of the waist belt up through the buckle to form a loop A . • Pull the free end of the waist belt B . • Repeat this procedure to tighten the other waist belt. To loosen the waist belts: • Feed the free end of the waist belt up through the buckle to form a loop A . • Enlarge the loop by pulling on the end of the loop toward the buckle. • Pull the anchored end of the waist belt to shorten the free end of the waist belt B . • Repeat this procedure to loosen the other waist belt. Anchored End Anchored End Free End Free End Buckle 3 Secure Child 5 Hold Adjuster Pull Down Strap Slide Adjuster Down TIGHTEN LOOSEN To tighten the shoulder belts: Hold the adjuster and pull the front shoulder strap down. To loosen the shoulder belts: Slide the adjuster down. Note: After adjusting the restraint system to fit your child, make sure you pull on it to be sure it is securely fastened. 4 Shoulder Portion • From the front of the high chair, pull the shoulder portion of the waist/shoulder belts out and then fit them back through the desired shoulder belt slots in the headrest pad, seat pad and the seat back. • Pull on the belts to be sure they are secure in the seat back. 6 T...