Votes - 2, Average rating: 4
(
)
)
|
manual abstract
Tool needed for assembly: Phillips Screwdriver (not included). Product features and decoration may vary from the photo above. ™ IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. WARNING Healthy Care High Chair Model Number: B8866 Please read these instructions before assembly and use of this product. Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included). Product features and decoration may vary from the photo above. ™ IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE. WARNING 2 Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us, rather than return this product to the store. Usually, we can solve the problem over the telephone or send you replacement parts. Please call 01628 500303 or write to: Mattel UK Limited Mattel House Vanwall Business Park Vanwall Road Maidenhead, Berkshire SL6 4UB This product contains small parts in its unassembled state. Adult assembly is required. Consumer InformationWarnings and Caution Prevent serious injury or death from falls or sliding out. • The child should at all times wear a safety harness correctly fitted and adjusted. • The tray is not designed to hold the child in the chair. • Always keep child in view while in the high chair. •Never leave child unattended. • It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted. WARNING CAUTION 2 Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us, rather than return this product to the store. Usually, we can solve the problem over the telephone or send you replacement parts. Please call 01628 500303 or write to: Mattel UK Limited Mattel House Vanwall Business Park Vanwall Road Maidenhead, Berkshire SL6 4UB This product contains small parts in its unassembled state. Adult assembly is required. Consumer InformationWarnings and Caution Prevent serious injury or death from falls or sliding out. • The child should at all times wear a safety harness correctly fitted and adjusted. • The tray is not designed to hold the child in the chair. • Always keep child in view while in the high chair. •Never leave child unattended. • It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted. WARNING CAUTION Parts 3 Seat Bottom 2 Seat Bottom Tubes Seat Back Frame Frame Footrest 2 Bases 4 Screw Retainers Hinge Rod Base Tray Food Tray Pad #8 x 2 cm (3/4") Screws #8 x 1.9 cm (3/4") Screws #8 x 1.9 cm (3/4") Screws #10 x 2.2 cm (7/8") Black Screws #10 x 2.2 cm (7/8") Black Screw - 4 #10 x 2.2 cm (7/8") Black Screw Toy #8 x 1.9 cm (3/4") Screw - 8 SHOWN ACTUAL SIZE #10 x 2.2 cm (7/8") Black Screw - 7 SHOWN ACTUAL SIZE Note: Tighten all screws with a Phillips screwdriver.Do not over-tighten the screws. • Place the seat bottom face down on a flat surface. • At an angle, fit the footrest on the seat bottom, as shown. Seat Bottom Footrest IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing, damaged or broken. Contact Mattel for replacement parts and instructions if needed.Never substitute parts. Assembly • Slide a seat bottom tube through each set of plastic rings on the seat bottom. • Align the holes in the plastic rings and the seat bottom tubes. • Insert a #8 x 1.9 cm (3/4") screw into each plastic ring and tighten. • Push the seat bottom tubes back and forth to be sure they are secured to the seat bottom. If the seat bottom tubes move, you have probably not fastened them properly. Remove the screws and check to be sure the screw holes in the seat bottom tubes and seat bottom plastic rings are aligned. Replace and tighten the screws. • Insert two #10 x 2.2 cm (7/8") black screws through the footrest and into the seat bottom. • Tighten the screws. Footrest Insert Screws Here 4 Plastic Rings Plastic Rings Seat Bottom Tubes Plastic Rings Plastic Rings Seat Bottom Tubes 1 2 4 3 #8 x 1.9 cm (3/4") Screw- 4 SHOWN ACTUAL SIZE #10 x 2.2 cm (7/8") Black Screw - 2 SHOWN ACTUAL SIZE • Turn the seat bottom assembly upright. • Fit the seat back pins into the openings in the top side of the seat bottom assembly. Seat Bottom Assembly Seat Back Pin Seat Back Pin Opening Opening Assembly • Turn the seat assembly face down. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. • Insert a #10 x 2.2 cm (7/8") black screw into the hinge rod and tighten. • Set the seat assembly aside for Assembly step 10. • Pull the frame leg out on each frame to open.Make sure it “clicks” into place. 5 Hinge Rod Hinge Frame Leg 5 6 7 #10 x 2.2 cm (7/8") Black Screw SHOWN ACTUAL SIZE Assembly • While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown. 6 Seat Height Adjusters Position 4 • Position a f...