Votes - 4, Average rating: 4
(
)
)
|
manual abstract
IMPORTANT - It may be necessary to remove the adaptors from the child seat when installing it in your vehicle. If the adaptors are in contact with the vehicle seat cushion, remove them. To remove the adaptors from the child seat, pull the lever on the adaptors away from the child seat while pulling down (dia 2e). Repeat the process for both adaptors. The child seat is compatible with the ISOFIX base (purchased separately). See for further information. Only use a P-Type child seat on this buggy when fitted with a Verve P-Type socket HANDY HINT - You may find it easier to apply the brake when fitting the child seat. Please refer to the user guide for your buggy. Clip the socket onto the chassis from the inside. Align the bottom edge of the socket with the edge shown on the chassis (dia 2a). Rotate the fixing arm. Squeeze the housing and fixing arm together with one hand and snap over the hook with the other hand. Repeat this process for both sockets. Ensure that the left hand and right hand sockets are used on the correct side of the buggy. To fit the adaptor to the child seat squeeze the lever and insert into the space below the handle (dia 2b). Make sure it is fully fitted and release the lever to lock into place. Repeat this process for both adaptors. Ensure that the left hand and right hand adaptors are used on the correct side of the child seat. IMPORTANT - The buggy seat unit must be removed before attaching your car seat. Lower the child seat onto the buggy making sure that the adaptor on either side drops into both the sockets on each side of the buggy (dia 2c). Push down firmly. Once the seat is engaged you will hear a click. Move the handle to the rocking position. Please refer to the user guide for the child seat. WARNING - Check that the child seat attachment devices are correctly engaged before use. IMPORTANT - Ensure your child is harnessed at all times. Unclip the hooks on both sides of the buggy (dia 1d). Remove the seat unit from the chassis by sliding the base tabs upwards and out of the grooves. Then slide the top tabs upwards and out of the grooves until the seat unit is disengaged (dia 1e). To re-fit the seat unit reverse these instructions. HANDY HINT - You may find it easier to apply the brake before removing or re-fitting the seat unit. Please refer to the user guide for your buggy for operation of the brake. Unfasten the press studs on the backrest and unfasten the hook and loop fastenings on both sides of the seat unit where it overlaps the hood (dia 1a). HANDY HINT - You may find it easier to stand behind or to the side of the buggy. Remove the hood and bumper bar by simultaneously pressing the buttons on the mouldings on both sides of the buggy and slide them upwards until they disengage (dia 1b). Unfasten the hook and loop fastenings and press studs shown by the red circles (dia 1c). 1 Removing or re-fitting your seat unit (the seat cover must be removed before fitting the infant carrier) B A BBO-662-00 B A 1a 1b 1c 1d B B A A 1e 2a 2b 2c 2d 2e 1282.000 - Verve Adaptors & Sock1 1 10/1/07 09:15:40 WARNING – A CHILD’S SAFETY IS YOUR RESPONSIBILITY Read these instructions carefully before use and keep them for further reference. Your child’s safety may be affected if you do not follow these instructions. IMPORTANT! Please read this User Guide carefully BEFORE trying to use your buggy Looking after your buggy The buggy and its cover have been carefully designed, manufactured and tested to high safety standards. Regularly inspect and maintain your buggy to ensure freedom of movement of the locking devices and security of components. To prolong the life of your buggy, keep it clean and do not leave it in direct sunlight for extended periods of time. Helpful hints Regularly clean and inspect your buggy. To ensure trouble free operation lubricate moving parts and joints with a silicon based spray. If the wheels squeak use a silicon based spray or light lubricating oil ensuring it penetrates the wheel and axle assembly. When using the buggy on the beach, clean it completely afterwards to remove all the sand and salt from the mechanisms and wheel assemblies. Under certain climate conditions the covers and trims may be affected by mould and mildew. To help prevent this occurring, do not fold or store this buggy if it is wet or damp. Always store in a well ventilated area. Cleaning the cover The hood, seat covers and trims may be cleaned using warm water with household soap or mild detergent. Allow it to dry fully, away from direct sunlight. DO NOT dry clean or use bleach or any other aggressive cleaning agents. To maintain the safety of your buggy, seek prompt repairs for bent, torn or broken parts. Use only those parts and accessories approved by Britax. Replacement parts and accessories are available from your Britax stockist or contact Britax Customer Service Department on 01264 386034. This product is not intended for commercial use. Guarantee All Britax products are carefu...