Orient a strip of nails with the points down, and drop the strip of nails into the Magazine (part #71). (See Figure C.) 4. Slide the strip of nails forward in the Magazine (part #71). NOTE: The Magazine will hold 60, 10 gauge nails. (See Figure C.) 5. Unlatch the Feeder Shoe (part #52), and allow the Feeder Shoe to slide forward against the strip of nails. (See Figure C.) OPERATION NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 11. 1. Adjust the

For technical questions and replacement parts, please call 1-800-444-3353 Specifications Air Inlet 1/4 ”-18 NPT Recommended Air Pressure 60 -100 PSI, 100 PSI Max. Magazine Capacity 100 Nails or 80 Staples Safety Feature Single Sequential Safety Trip Mechanism Nail Size .039-.042” Shank (18 Gauge), 5/8 ” -11/ 4 ” L Staple Size 1/4 ” Crown, .039-.042” Shank (18 Gauge), 1/2 ” -11/ 4 ” L Accessories Oil Dropper, 2 Wrenches, 1 Coupler Plug Save This Manual You will need the manual for the safety warn

SKU 41209 For technical questions, please call 1-800-444-3353. Page 5 Unpacking Unpacking Operation For best service, you should incorporate an oiler, regulator, and inline filter, as shown in the diagram below. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. TO ROOFING NAILER Note: To connect this tool, we recommend you use the included quick connector. For smoother operation and to extend the life-span of the tool, put 3-5 drops of pneumatic tool oil

Other people in the work area must also wear ANSI approved impact safety goggles. Warning! Make sure the Nailer is not attached to the air hose whenever loading the tool. 1. Press the Magazine Latch (3-8) up and slide the Magazine Side Cover (3-1) back. 2. Holding the nailer with the nose pointing slightly down, insert the brad nails into the Magazine Side Cover (3-1), letting the pointed end ride on the rail of the Magazine Side Cover (3-1). 3. After the Nails reach the nose of the tool, close

Testing the Double Trigger Safety Mechanism Warning: Even though the nailer should be empty during this procedure, ALWAYS point the nailer at a piece of scrap wood when testing. 1. Make sure the tool is disconnected from the power supply. 2. Completely empty the magazine of nails. 3. The Nailer should not fire if the second trigger Safety Trigger (123) Trigger (125) Figure 1 is not pulled. 4. Check that the Trigger (125) and the Safety Trigger (123) move freely, without sticking see Figure 1. 5.

Connect the Air Source Hose to the Air Plug (41). Note: If you are not using an automatic oiler system on your air compressor, before operation, add a few drops of Pneumatic Tool Oil to the airline connection. Remove the air line at the inlet and put 2 or 3 drops of good quality air tool oil into the air fitting each day of use. With heavy, prolonged use, do this at least twice a day. 2. Set the air pressure on your compressor to 60-125 PSI. Do not exceed the maximum air pressure of 125 PSI. Not

2. While doing this step and the next, hold the Nailer pointed away from you and any other people or fragile objects. Pull the Quick Release Lever (49) forward to the position shown in Figure 2. Remove the Driver Guide Cover (51). 3. Remove the jammed nail. Pliers may be necessary to remove a stuck nail. 4. Inspect the Drive Pin (46) for bends or breakage -see location in Figure 3. If it is damaged, do not use the tool until it is repaired by a qualified technician. 5. Lightly oil the Drive Pin

If you are using the tool outdoors, use an extension cord rated for outdoor use. (signified by “WA” on the jacket). . Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician. Note: Performance of this tool (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. Special Warnings for this Tool It is especially important that you read and comply with the followin

2. USE ONLY CLEAN, DRY, REGULATED, COMPRESSED AIR AT BETWEEN 60 TO 115 PSI. Never use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. 3. NOTE: An air compressor is not provided. You will need an air compressor with a minimum rating of 4 to 6 CFM delivery at 90 PSI. 4. WHEN CONNECTING TO THE AIR SUPPLY: Prior to each use, if an automatic oiler is not used, add two drops of Air Tool Oil (part #95) into the Air Plug (part #33) of the Air Stapler.

reach of children and other untrained persons. A tool is dangerous in the hands of untrained users. Maintain the tool with care. f. A properly maintained tool is more efficient and reduces the risk of binding and is easier to control. Check for misalignment or bindg. ing of moving parts, breakage of parts, and any other condition that affects the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. There is a risk of bursting if