Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
RACKING THE FLOORING (SEE FIGURE 7) First refer to flooring manufacturer’s preparation procedures regarding moisture content and floor preparation before laying the flooring boards. To correctly install hardwood flooring, it must be properly racked before being nailed into place. After placing the first board, follow these instructions to rack the flooring: 1. Place flooring groove onto the tongue of previously installed board. 2. Use the rubber end of the mallet to “pop” the tongue into the groove. 3. Use the metal end of the mallet to rack the board tightly against adjacent board. UP Position of Shoe plate Figure 6 Figure 7 Alternate Racking View Racking Popping Figure 8 FIRING THE NAILER 1. Connect the air supply to the nailer. Note: Make sure the rubber bumper on the flooring nailer is in the up position before adding the air hose, if not, the nailer may cycle. 2. Load fasteners (see Loading the Nailer Section). 3. Place the tool on the floor as shown in Figure 8 with the shoe plate resting on the racked floor board. Make sure the fastener ejection nozzle is firmly placed against the board tongue. 4. Strike the tools rubber bumper firmly with the rubber end of the mallet. The tool should cycle and drive fastener into floor board. Do NOT fire the tool unless it is securely placed. If tool is not securely placed, there is a risk of flying fasteners that may cause death or serious injury. Modelo CHN50399 Notas FASTENER DEPTH & PLACEMENT Refer to Figure 9 for correct depth placement of fasteners in hardwood tongue. Use a scrap piece of the flooring to help determine correct air pressure settings. Damage to the tongue upon installation will make remaining project difficult. Fastener seated High Air Pressure too LOW Figure 9 Fastener seated Low Air Pressure too HIGH Fastener seated Correctly Air Pressure set Correctly 6 31 Sp Manual de Instrucciones y Lista de Piezas Informacion de intercambio de sujetadores Los sujetadores usados en la Clavadora/Agrapadora para Pisos CHN50399 de Campbell-Hausfeld sirven tambien para las siguientes marcas: Bostich, Porter Cable, Porta-nails, Primatech, Senco, Power Nail, Grip Rite, High Pro, B&C Eagle, Grizzly, y Craftsman. Guia de Diagnostico de Averias Deje de usar la clavadora inmediatamente si alguno de los siguientes problemas ocurre. Podria resultado en heridas graves. Cualquier reparacion o reemplazo de piezas los debe hacer un tecnico calificado personal de un centro autorizado de servicio. Problema Causa Solucion Fuerza insuficiente; 1 La herramienta esta demasiado 1. Anada lubricante ciclo lento seca 2. La presion de aire es insuficiente 2. Verifique el equipo de suministro de aire 3. El escape esta bloqueado 3. Limpie el escape No dispara el sujetador o alimentacion intermitente Sujetador atascado en la herramienta 1. El resorte del mecanismo de impulso esta danado 2. Se esta usando un sujetador de tamano inapropiado 3. El cargador o la placa de desgaste estan sucios 1. El canal del mecanismo de impulso esta desgastado 2. El mecanismo de impulso esta danado o desgastado 3. Los sujetadores estan doblados 30 Sp 1. Reemplace el resorte 2. Use sujetadores estandar 3. Limpie el cargador y la boquilla 1. Reemplace la placa de desgaste 2. Reemplace el mecanismo de impulso 3. Use sujetadores estandar Model CHN50399 Maintenance Technical Support Please call our Nailer Hotline at 1-800-543-6400 with any questions regarding the operation or repair of this nailer or for additional copies of this manual. Replacement Parts Use only genuine Campbell Hausfeld service parts. Tool performance, safety and durability could be reduced if improper parts are used. When ordering replacement parts, specify by part number. Nailer Repair Only qualified personnel should repair the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently. Fastener Interchange Information Fasteners used in the Campbell Hausfeld CHN50399 Flooring Nailer / Stapler will also work in the following brand units: Bostich, Porter Cable, Porta-nails, Primatech, Senco, Power Nail, Grip Rite, High Pro,B&C Eagle, Grizzly, and Craftsman. Troubleshooting Guide Stop using nailer immediately if any of the following problems occur. Serious personal injury could result. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center. Problem Cause Solution Lack of power; slow to 1. Tool is too dry 1. Add lubricant cycle. 2. Air pressure is low 2. Check air supply equipment 3. Exhaust is blocked 3. Clean exhaust Shooting no fastener or 1. Damaged pusher spring 1. Replace spring intermittent feeding 2. Wrong size fastener is being used 2. Use standard fasteners 3. Magazine or wear plate is dirty 3. Clean magazine and nose Fastener jammed in tool 1. Driver channel is worn 2. Driver is broken or worn 3. Fasteners are bent Assembly Procedure For Seals When repairing a nailer, the internal parts must be ...