Login:
Votes - 3, Average rating: 4.3 ( )

User manual Grizzly, model 1 1/4" Brad Nailer T20568

Manafacture: Grizzly
File size: 781.84 kb
File name: 896b5ad2-4427-47cf-8cdd-144976578e6a.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


10. For more assistance, or to install a complete o-ring set, refer to the breakdown diagram in the back of this manual for component locations. t20568 11.4" brad nailer -11 cleaning & lubrication cleaning use a good solvent to clean the nose assembly of the nailer. always be sure that the nailer is dry before using it again. do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may result in leaks and damage to the nailer and the air couplings. never use gasoline or other flammable liquids to clean this tool. vapors in the tool may ignite, causing the tool to explode. ignoring this warning may lead to serious personal injury or even death! lubricating pneumatic tool oil has been included with your new grizzly nailer to help maintain its useful life. place two to six drops of oil in the nailer air inlet (as shown in figure 8) before every use, or after 2 hours of continuous use. Wipe off any excess oil near the nailer exhaust to avoid dust build-up. When the oil that was included with the nailer has been completely used, replace with grizzly model g2820 pneumatic tool oil. another option to manual oiling would be to install a lubricator in your air compressor line. if your air compressor line already has a lubricator, then regular lubrication of your nailer will not be necessary. Just make sure there is always oil in the lubricator. figure 8. lubricating nailer via air inlet. -12-t20568 11.4" brad nailer troubleshooting symptom possible cause solution air leaking at trigger valve area. 1. o-rings in trigger valve housing are damaged. 1. o-rings must be replaced & operation of safety nose must be checked. air leaking 1. loose screws in housing. 1. tighten screws. between hous2. damaged o-ring. 2. replace o-ring. ing and hose. 3. loose air fitting. 3. tighten air fitting & use teflon tape. air leaking between housing and cap assembly. 1. damaged seal. 1. replace damaged seals. tool skips nails while discharging. 1. incorrect air pressure. 2. air leaks. 3. dirt in nose. 4. dirt or damage prevents nails from moving freely. 5. Worn piston o-ring or lack of lubrication. 6. damaged trigger valve o- rings. 7. Worn bumper. 8. Cap seal leaking. 1. use correct air pressure. 2. tighten screws and fittings. 3. Clean nose. 4. Clean magazine and inspect/ repair damage. 5. replace o-ring and lubricate. 6. replace trigger valve o-rings. 7. replace bumper. 8. replace cap seal. tool runs slowly or has a loss of power. 1. nailer is not lubricated. 2. broken spring in cap assembly. 3. exhaust port in cap is blocked. 1. lubricate nailer. 2. replace spring. 3. Clean or replace damaged internal parts. Fasteners frequently jam the nailer. 1. nails are the wrong size. 2. nails are bent or dirty. 3. magazine or nose screws are loose. 4. driver or driver guide are worn or damaged. 5. nails are wrong angle. 1. use correct nails. 2. use undamaged, clean nails. 3. tighten magazine. 4. replace worn or damaged parts. 5. use correct angle nails. nailer does not fire. 1. nailer is not lubricated. 2. nail is jammed in magazine or discharge area. 3. piston shaft is damaged. 4. air pressure too low. 1. Follow lubricating instructions. 2. Clear nailer magazine or discharge area. 3. replace piston shaft. 4. Check/increase air pressure. air blows out of exhaust cap; nailer will not fire. 1. o-ring damaged or slipped out of groove on switch piston, inside the nailer. 1. reinstall/replace suspect o-ring; turn down the air pressure to prevent it happening again. t20568 11.4" brad nailer -13 t20568 parts breaKdoWn & ' ( ) * + , ....' ..* ..+ .., .... . ..( ..) ..* ..+ .., .... * ..+ .., .... . ..% ..& ..' ..) ..( ..' ..* ..+ .., .... . ..% ..& . ..% ..& ..' ..' ..% , ... ......& ..' ......) ..( ..) ..* ..+ .., ....... ... ..% ..& ..+ .., ........ ) ..* ..( ..) ..& ..' ..* ..% ..& ..' ..........* ..+ .., .... . ..% ..& ..' ................ -14-t20568 11.4" brad nailer t20568 parts list REF PART # DESCRIPTION REF PART # DESCRIPTION PT20568001 STEEL BALL 2.5MM PT20568002 ORIENTATION SPRING PT20568003 SHOULDER BOLT M4-.7 X 16 PT20568004 DIRECTION SPRING PT20568005 AIR DEFLECTOR PSB15M CAP SCREW M5-.8 X 20 PLW01M LOCK WASHER 5MM PT20568008 CYLINDER CAP PT20568009 SEALING WASHER 18MM PT20568010 O-RING 17 X 2.65 PT20568011 COMPRESSION SPRING PT20568012 O-RING 33.6 X 2 PT20568013 SWITCH PISTON PT20568014 GASKET PT20568015 O-RING 30 X 3 PT20568016 O-RING 23.5 X 2 PT20568017 MAIN PISTON PT20568018 O-RING 41.7 X 3 PT20568019 COLLAR PT20568020 CYLINDER PT20568021 BUMPER PT20568022 PISTON SLOT WASHER PT20568023 GUN BODY PT20568024 DIRECTION SEAT PRP55M ROLL PIN 3 X 27 PT20568026 SPRING SEAT PT20568027 COMPRESSION SPRING PT20568028 ADJUSTMENT SEAT PT20568029 ROLL PIN 1.5 X 8 PT20568030 COMPRESSION SPRING PT20568031 ADJUSTMENT WHEEL PT20568032 ADJUSTMENT BOLT PT20568033 SAFETY GUARD PT20568034 RING PSB80M CAP SCREW M3-.5 X 8 PT20568036 O-RING 7 X 1.5 PT20568037 TRIGGER VALVE GUIDE PT20568038 COMPRESSION SPRING PT20568039 O...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category