Manafacture: Bosch File size: 1.38 mb File name: Language of manual:

Free link for this manual available at the bottom of the page

1. Loosen the hose clamp, remove the drainage hose carefully (residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock Do not immerse the HydroSafe safety device in water (it contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except Spin/Rinse / Empty). 3. Press Start/Reload. Let the programme run for approximately 40 seconds. 4. Turn the programme selector to Off. Disconnect the mains plug. Clean the filter: 5. Disconnect the hose from the tap. Clean the filter with a small brush. and/or for Standard and Aqua-Secure models: Remove the hose from the back of the appliance, Remove the filter using pliers and clean the filter. 6. Connect the hose and check for leaks. Risk of scalding . Allow the detergent solution to cool down. . Turn off the tap. What to do if... . . . . . . . . . . . . . . . . . Water is leaking out. . Attach/replace the drainage hose correctly. . Tighten the screw connection of the supply hose. No water supply. Detergent not dispensed. . Start/Reload not pressed? . Tap not turned on? . Filter blocked? Clean the filter ..page 11. . Supply hose kinked or trapped? Washing machine door cannot be opened. . Safety function active. Programme stopped? ..page 4. . (Rinse Hold = no final spin) selected? ..page 3, 4. . Can be opened by emergency release only? ..page 13. Programme does not start. . Start/Reload pressed or "Finish in" time selected? . Washing machine door closed? . Childlock active? Deactivate ..page 5. Detergent solution does not drain. . (Rinse Hold = no final spin) selected? ..page 3, 4. . Clean the detergent solution pump ..page 11. . Clean the waste pipe and/or drainage hose. Water not visible in the drum. . Not a fault -water below the visible area. Spin result not satisfactory. Laundry wet/too damp. . Not a fault -the unbalanced-load detection system interrupted spinning, uneven laundry distribution. Distribute large and small items of laundry evenly in the drum. . Less Ironing selected? ..page 5. . Speed selected too low? ..page 5. The programme duration changes during the washing cycle. . Not a fault -the programme sequence is optimised for the relevant washing process. This can cause changes in the programme duration in the display panel. Drum spins gently several times. . Not a fault -unbalanced-load detection system is adjusting the imbalance. Residual water in the ~ compartment for care products. . Not a fault -the action of the care product is not affected. . Clean the insert if necessary ..page 10. Odours in the washing machine. . Run programme Cotton 90 °C without laundry. Use standard detergent. Status display..t flashing. Detergent may escape from the detergent drawer. . Too much detergent used? Mix 1 tablespoon of fabric softener with . litre of water and pour into compartment II (not for outdoor or down fabrics). . Reduce the detergent dosage for the next wash cycle. Loud spinning, vibrations and .walking. during the spin cycle. . Are the appliance feet fixed? Secure appliance feet ..Installation instructions. . Transportation safety devices removed? Remove transportation safety devices ..Installation instructions. Noises during spinning and draining. . Clean the detergent solution pump ..page 11. Display panel/indicator lamps do not function during operation. . Power cut? . Circuit breakers tripped or fuses blown? Reset the circuit breakers or change the fuses. . Energy saving mode active? . If the fault occurs repeatedly, call the after-sales service. Programme sequence longer than usual. . Not a fault -unbalanced-load detection system is adjusting the imbalance by repeatedly redistributing the laundry. . Not a fault -foam detection system active -adds an additional rinse cycle. There is detergent residue on the laundry. 12 . Occasionally, phosphate-free detergents contain water-insoluble residues. . Select Spin/Rinse or brush out the laundry after washing. What to do if... . In reload mode, Start/Reload flashes very quickly and a signal sounds . Water level too high. Not possible to add more laundry. Close the washing machine door immediately if necessary. . To continue the programme, press Start/Reload. If you cannot correct a fault yourself (switching on/off) or a repair is required: . Turn the programme selector to Off and remove the mains plug from the socket. . Turn off the tap and call the after-sales service a page 13. Erelease e.g. in the event of a power cut mergency The programme continues when the power supply is restored. However, if the laundry has to be removed, the washing machine door can be opened as follows: Risk of scalding! The detergent solution and laundry may be hot. If possible, leave to cool down. Do not reach into the drum if it is still rotating. Do not open the washing machine door if water can be seen through the glass. 1. Tur...

Other models in this manual:
Washers - WM14S496GB/20 (1.38 mb)
Washers - WM14S496GB/23 (1.38 mb)
Washers - WM14S496GB/38 (1.38 mb)
Washers - WM16S496GB/20 (1.38 mb)

Download now

Please, enter two numbers from picture: