Votes - 0, Average rating: 0 ( )

Manafacture: Bosch File size: 2.15 mb File name: Language of manual:

..: ...., .... Open the tap completely, supply hose kinked or trapped; Clean the filter .. page 11, water pressure too low. ..: .... Detergent solution pump blocked; Clean the detergent solution pump .. page 11. Drainage hose/waste pipe blocked; Clean the drainage hose at the siphon .. page 11. ..: .... Water in the base tub, appliance leaking. Call the after-sales service. ..: ...., .... Washing machine door cannot be locked. Open the washing machine door and close it with an audible "click"; switch the appliance off and on again; set the programme and make your settings; start the programme. ..: ...., ...., .... Motor fault. Call the after-sales service. Other displays Switch off the appliance, wait for 5 seconds and switch it back on. If the display appears again, call the after-sales service .. page 13. – Risk of electric shock. Disconnect the mains plug. – Risk of explosion. No solvents. 11 Information about blockages Detergent solution pump Turn the programme selector to Off and disconnect the mains plug. 1. Open and remove the service flap. 2. Take the drainage hose out of the retainer. Remove the sealing cap, allow the detergent solution to flow out. Push the sealing cap back on. 3. Unscrew the pump cover carefully (residual water). 4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must be able to rotate). 5. Replace the pump cover and screw it on tightly. The handle points upright. Replace the drainage hose in the holder. 6. Refit the service flap and close it. To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into compartment II and start the .. Empty programme. Drainage hose at the siphon Turn the programme selector to Off and disconnect the mains plug. 1. Loosen the hose clamp, remove the drainage hose carefully (residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock Do not immerse the AquaStop safety device in water (it contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except for .. Spin/.. Empty). 3. Select .. Start/Pause. Let the programme run for approximately 40 seconds. 4. Turn the programme selector to Off. Disconnect the mains plug. Clean the filter: 5. Disconnect the hose from the tap. Clean the filter with a small brush. and/or for Standard and Aqua-Secure models: Remove the hose from the rear of the appliance. Remove the filter with pliers and clean. 6. Connect the hose and check for leaks. Risk of scalding – Allow the detergent solution to cool down. – Turn off the tap. What to do if ... . . . . . . . . . . . . . . . . Water is leaking out. – Attach/replac– Tighten the sce the drainage hose correctly. rew connection of the supply hose. No water supply. Detergent not dispensed. – (Start/Pau– Tap not turne– Filter blocked– Supply hose kse) not selected? d on? ? Clean the filter a page 11. inked or trapped? Washing machine door cannot be opened. – Safety functio– (Rinse Stop – Can be openen active. Programme termination? a page 4. = no final spin) selected? a page 3,4. d by emergency release only? a page 13. Programme does not start. – (Start/Pau– Washing macse) or (Finish in) time selected? hine door closed? Detergent solution does not empty. – (Rinse Stop – Clean the det– Clean the was= no final spin) selected? a page 3,4. ergent solution pump a page 11. te pipe and/or drainage hose. Water not visible in the drum. – Not a fault -water below the visible area. Spin result not satisfactory. Laundry wet/too damp. – No fault -the spinning, uneDistribute larg– S (Less Ironi– Speed selecteunbalanced-load detection system interrupted ven laundry distribution. e and small items of laundry evenly in the drum. ng) selected? a page 5. d too low? a page 5. The programme duration changes during the wash cycle. – Not a fault – tparticular wasprogramme dhe programme sequence is optimised for the h process. This may result in changes to the uration in the display field. Drum spins gently several times. – Not a fault -uimbalance. nbalanced-load detection system is adjusting the Residual water in the compartment 0 for care products. – Not a fault -th– Clean the insee action of the care product is not affected. rt if necessary a page 10. Odour formation in the washing machine. – Run programstandard deteme E Cottons 90 °C without laundry. Use rgent. Status display..t (Wash) flashes. Detergent may be leaking out of the detergent drawer. – Too much detMix 1 tablespointo compartm– Reduce the dergent used? on of fabric softener with . litre of water and pour ent II (not with outdoor or down fabrics). etergent dosage for the next wash cycle. Loud spinning, vibrations and “wandering” during the spin cycle. – Are the appliaSecure applia– Transportation Remove transinstructions. nce feet fix...

Download now

Please, enter two numbers from picture: