Votes - 0, Average rating: 0
(
)
)
|
manual abstract
2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock! Do not immerse the Aqua-Stop safety device in water (contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except Rinse .. / Spin .. // Empty ..). 3. Choose ....Start/Reload. Let the programme run for approximately 40 seconds. 4. Turn the programme selector to Off. Disconnect the mains plug. Clean the filter: 5. Disconnect the hose from the tap. Clean the filter using a small brush. and/or for Standard and Aqua-Secure models: Remove the hose on the rear of the appliance. Remove the filter with pliers and clean. 6. Connect the hose and check for leaks. . Risk of burning! Allow the detergent solution to cool. . Turn off the tap. 11 What to do if... .. Water is leaking out . Attach/replace the drainage hose correctly. . Tighten the screw connection of the supply hose. .. No water supply. Detergent not dispensed. . ....Start/Reload not selected? . Tap not turned on? . Filter blocked? Clean the filter ....page 10. . Supply hose kinked or trapped? .. The appliance door will not open. . Safety function active. Programme stopped? ....page 4. . .. (without final spin) selected? ....page 3, 4. . Can be opened by emergency release only? ....page 9. . Door locked after the washing machine is switched off: Switch on the washing machine and wait for 5 seconds. .. The selected programme does not start. . ....Start/Reload or .. (Ready in) time selected? . Washing machine door closed? . Childproof lock active? Deactivate ....page 5. .. Detergent solution is not drained. . .. (without final spin) selected? ....page 3, 4. . Clean the detergent solution pump ....page 10. . Clean the waste pipe and/or drainage hose. .. No water can be seen in the drum. . Not a fault. Water remains inside below the visible area. .. Spin result not satisfactory. Laundry wet/too damp. . Not a fault. Spin control system has stopped the spin cycle. Uneven distribution of laundry. Distribute large and small items of laundry evenly in the drum. . Easy-iron .. selected? ....page 5. . Selected speed too low? ....page 5. .. Programme duration changes suddenly during operation. . Not a fault. The program time can vary according to the distribution of laundry, with it therefore being possible for the display panel to show adjustments in the duration. .. Spin cycle performed several times. . Not a fault. The balance control system has detected an imbalance and is attempting to redress this by repeating the spin. .. Residual water in the compartment for care products. . Not a fault: the action of the care product is not affected. . Clean the compartment if necessary ....page 9. .. Odour formation in the washing machine. . Run programme Cottons ....90 °C without laundry. Use standard detergent. .. Status display .. flashing. Appliance has detected a detergent overload. . Too much detergent used? If foam is escaping from the detergent drawer: mix 1 tablespoon of fabric softener with . litre of water and pour into compartment II (not with outdoor or down fabrics). . Reduce the detergent dosage for the next wash cycle. .. Intense noise formation, vibrations and "wandering" during the spin cycle. . Are the appliance feet fixed? Secure the appliance feet ....Installation instructions. . Transportation safety devices removed? Remove transportation safety devices ....Installation instructions. .. Display panel/indicator lamps remain turned off while the machine is working. . Energy-saving mode ....page 5. . Power cut? . Fuses triggered? Reset/change the fuse. . If the fault occurs repeatedly, call customer services. .. Programme sequence longer than usual. . Not a fault. Unbalanced load detection system adjusts imbalance by repeatedly distributing the laundry. . Not a fault: foam detection system active; adds an additional rinse cycle. .. Detergent residues on the laundry. . Occasionally, phosphate-free detergents contain water-insoluble residues. . Select Rinse .. / Spin .. or brush out the laundry after washing. If you cannot correct a fault yourself or if a repair is necessary: . Turn the programme selector to Off and remove the mains plug from the socket. . Turn off the water supply and call customer services ....Installation instructions. Washing machine en Instruction manual 1 2 .. - 90 °C .. (temp. .C) Select the temperature (.. = 1 - 24 h .. (Ready in) End of programme after ... .. - 1200* .. (rpm) Select the spin speed (* depe laundry soaks in the last rins Status displays Programme sequence displa ..................- ....- Wash, rinse, spin, programm .. Childproof lock ....page 5 .. Open the washing m Correct installation according to the separate installations actions. Checking the machine . Never use a damaged machine! . Contact customer service! Connecting the mains plug Make sure your hands are dry! Handle...