Votes - 0, Average rating: 0
(
)
)
|
manual abstract
The information contained can save you time and effort and will help to ensure optimum performance of your new washer. Be sure to observe all warnings and cautions. NOTICES . Frozen hoses can tear or burst. Do not install the washing machine outdoors or in an area exposed to freezing condtions. . If the washing machine is located in a room which will be exposed to temperatures below freezing, or if it is located in a cabin that is being shut down for the winter, any residual water in the pump or water inlet hose(s) must be drained. . Take care not to damage the washing machine. Do not hold on to protruding parts (e.g. door) when lifting. . In addition to the safety information listed here, the local water and electricity supplier may have special requirements. . If in doubt, have the appliance connected by an authorized technican. These installation instructions are intended for use by qualified installers. In addition to these instructions, the installation must comply with: -for the United States - National Electrical Code, ANSI/ NFPA70 - and latest editions of the State and municipal and/or local regulations. -for Canada - Canadian Electrical Code C22.1 - and the latest editions of the Provincial, Municipal and/or local regulations. Tools needed The following tools may be helpful during installation of your washer. . 13mm socket for removing the transport bolts. . 17mm wrench for adjusting the appliance feet. . Bubble level for leveling the appliance. Waste disposal Disposal of Packaging Materials After unpacking your new appliance dispose of the protective packaging materials in an environmentally friendly way. Ask your dealer or inquire with your local authority regarding currently acceptable means of disposal. 9 WARNING WARNINGS FOR CHILDREN Do not let children play with packaging and associated parts to avoid risk of choking or suffocation. Disposal of Your Old Appliance Your old appliance can be recycled if it is no longer to be used. Prior to disposing of your old appliance observe the following precautions to reduce safety risks. 9 WARNING TO AVOID RISK OF INJURY OR DEATH, DO THE FOLLOWING -after unplugging the old appliance, remove the electric power cord and dispose of properly. -remove the door or permanently disable the door lock to prevent children from being locked inside. Parts provided with your washer Washer drum contents 2 water supply hoses are shipped in the washer drum. Back side of the washing mashine Be sure to remove each of these items from the drum before using the washer. # + 3 ( Power cord with plug H Hot water connection 0 Literature pack; contents: P Cold water connection . User manual NOTICE: If any parts are missing please notify your . Warranty dealer immediately. . Covers with hose holders 8 Drain hose Set up on a pedestal with drawer Pedestal item number: WMZ 20490 @ Elbow to form the hose to fit the drain pipe Mount washer on the pedestal according to the instructions in the installation kit. Installation checklist Review the following list and check off each step as it is completed during installation. e Installation Step Page If installing to a pedestal (base), com-12 plete the base installation before removing the transportation bolts Completely remove all four shipping 12 bolts keeping the bolt and bushing assemblies intact Connect the water supply hose and 12 drain hose Connect the electrical power 15 Slide the washing machine into its final location Level the washing machine (as low as 14 possible) Before washing laundry, run a mainte-23 nance cycle 12 Importance of installing on a solid, level floor Your new Bosch washing machine utilizes high spin speeds to achieve superior water removal from your laundry resulting in reduced drying time. It is important to install your washing machine on a floor that will provide firm support. This prevents the washer from experiencing excess vibration during spinning that could cause the washer to move or be noisy. The installation surface must be solid and level in both directions. Avoid installing your washer on soft surfaces such as floors with carpet or foam backed covering material. If installing the washer on a wooden floor, observe the following: . install the washer in a corner for better support if possible. . if necessary, reinforce the floor by screwing a water resistant wooden board to the floor (minimum of 1.18 in./30 mm thick). . secure the front feet of the washing machine with holding brackets. A set of holding brackets can be obtained from a specialist store or from Customer Service (part number WMZ 2200). Remove the transport bolts 9 CAUTION DAMAGE TO THE APPLIANCE . The machine is secured for transport with transport bolts. Transport bolts that are not removed can damage the drum during operation of the machine, the washer will vibrate, and it will be much noisier during spin cycles if the transport bolts are not removed before use. Be sure to remove all 4 transport bolts completely before first use. Keep th...