Votes - 1, Average rating: 5
(
)
)
|
manual abstract
Straighten fill hoses 3. Water does not drain away Kink in discharge hose. House drain is blocked Straighten discharge hose. Clean drain 4. Water on floor around the washing machine Leaking gasket between tap and water inlet hose. House drain is blocked Soap drawer blocked with soap residues Replace gasket and tighten hose and tap well. Clean drain Clean soap drawer 5. Does not spin Water has not yet drained away. "No spin" selected (certain models only). Wait a few minutes for machine to empty. Reset button or turn "no spin" knob. 6. Machine vibrates a lot during spin Washing machine not completely level. Transit brackets not removed yet. Load not distributed evenly. Adjust the special adjustable feet. Remove transit brackets. Rearrange the laundry evenly. 7. Door will not open Two minutes have not elapsed since the programme finished. Wait two minutes. The machine makes a different noise when spinning! This is because it has a brush motor for better performance. Only a small level of water can be seen in the drum! This is because new machines do not use much water, yet achieve the same standard of washing and rinsing. 23 Note: The use of environmentally-phosphate- - waste water from suspension, without - presence of white powder the fabric and does not alter - The presence of foam in the rinsing. - Anionic surfactants used in washing to remove from the laundry itself and, even foam production. - Carrying out more rinse cycles does not serve CUSTOMER SERVICE AND GUARANTEE Your new appliance is fully guaranteed by the manufacturer for 12 months electrical/mechanical breakdown excluding: A. Any faults which occur due to bad installation or misuse of the machine. B. Any faults which occur due to repair of, or interference with, the machine by any not authorised by the manufacturer to carry out service. C. Any faults which arise from parts fitted to the machine which are not the manufacturers original parts. D. Any faults arising from non-domestic use or unusual or abnormal use of the machine. E. Any faults arising from operation at an incorrect voltage. F. Any faults arising from incorrect operation of the machine. The guarantee applies to Gt. Britain and Northern Ireland only, and is an addition to your statutory rights. After Sales Service If, having investigated the possible malfunctions on the chart on the previous page, you believe the appliance is not working correctly, please call our After Sales Service dept. on telephone number: Fig. 2 Technical data ¦ Max. load of dry laundry for washing ¦ Water pressure Measurements ¦ Width ¦ Depth ¦ Height 5,5 kg 0,05 . 0,8 MPa 60 cm 54 cm 82 cm EC Appliance complies with European Directive 89/336/EEC, 73/23/EEC and subsequent amendments. NB: For specifications regarding electrical data, see the data panel on the front of the washing machine (porthole area) - as shown in diagram above. Gias Service - Tel: 08705 400 600 Support Service (Eire 018301 666) 24 25 Note: we recommend you keep the transit bracket, braces and screws to immobilise the machine for future transit. The Manufacturers will not be responsible for any possible damage to the machine caused by not following the rules relating to releasing the mechanism. The user is responsible for all costs of installation. Water connection The appliance must be connected to the water mains using new hose-sets. The old hose-sets should not be re-used. The machine has an inlet hose with 3/4" B.S.P threaded end connection to attach between the threaded connector on the appliance and the cold water supply. This machine only uses cold water, therefore only one hose is needed to connect to the cold water supply. Do not connect to the hot supply. Cold fill is an energy efficient system. Only the water required for the washing is heated.There is no loss of heat in the pipeline from a hot water tank or boiler to the machine. 27 min 50 cm max 85 cm +2,6 mt max max 100 cm min 4 cm SETTING UP + INSTALLATION Remove the polystyrene base and place the machine near its permanent position (diagram 1). Carefully cut through the hose retaining clip at the rear of the appliance (diagram 2). Unscrew the central bolt (A); unscrew the 4 lateral screws (B) and remove the cross piece (C).Unscrew the two rods D and remove them. Two plastic spacers will fall inside the machine. (diagram 3). Lean the machine forward, remove the mentioned plastic spacers and remove the plastic bags containing the two polystyrene blocks at the sides, pulling downwards. (diagram 4). Stop the holes using the plugs that you will find inside the bag containing the instruction booklet. (diagram 5). WARNING: DO NOT LEAVE THE PACKAGING WITHIN REACH OF CHILDREN AS IT IS A POTENTIAL SOURCE OF DANGER. Apply the insulation sheet of corrugated material to the base as shown. Level the machine using the 4 feet. a) Turn the nut clockwise to release the screw adjuster on the foot. b) Rotate the foot to raise or lower it until it stands firmly on the ground. c) Lock the foot in...