Votes - 1, Average rating: 3
(
)
)
|
manual abstract
Make sure the adapter locks into place. O NOTE- • After connecting inlet hose to water tap, turn on the water tap to flush out foreign substances (dirt, sand or sawdust) in the water lines. Let water drain into a bucket, and check the water temperature. • Make sure that there are no kinks in the hose and that they are not crushed. ► When your washer has two valves. • The Inlet hose which has red connector is for the hot water tap. • If the washer has two valves, the energy is saved by using hot valve. ©NOTE After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor. Please use the horizontal tap Horizontal tap ¿¡5^] Extension tap JsL Et- Square tap 13 Installation ■ Installation of drain hose The drain hose should not be placed higher than 100 cm above the floor. Water in the washer does not drain or drains slowly. Securing the drain hose correctly will protect the floor from damage due to water leakage. If the drain hose is too long, do not force back into the washer. This will cause abnormal noise. • When installing the drain hose to a sink, secure it tightly with string. • Securing the drain hose correctly will protect the floor from damage due to water leakage. H14 Installation ■ Leveling 1. Leveling the washing machine properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room. O NOTE- > Timber or suspended type flooring may contribute to excessive vibration and unbalance. 2. If the floor is uneven, turn the adjustable feet as required. (do not insert pieces of wood etc. under the feet) Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level. (use a spirit level) • Once the washer is level, tighten the lock nuts up towards the base of the washer. All lock nuts must be tightened. • Diagonal Check When pushing down the edges of the washing machine top plate diagonally, the machine should not move up and down at all (Please, check both directions). If machine rocks when pushing the machine top plate diagonally, adjust the feet again. ©NOTE- • If the washing machine is installed on a raised platform, it must be securely fastened in order to eliminate the risk of falling off. 15 Installation ► Concrete floors • The installation surface must be clean, dry and level. • Install washer on a flat hard floor. ► Tile floors (Slippery floors) • Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed.) • Tread Mate is a self adhesive material used on ladders & steps that prevents slipping. Rubber Cup ► Wooden floors (Suspended floors) • Wooden floors are particularly susceptible to vibration. • To prevent vibration we recommend you place rubber cups under each foot under washer at least 15mm thick, secured to at least 2 floor beams with screws. • If possible install the washer in one of the corners of the room, where the floor is more stable. • Fit the rubber cups to reduce vibration. • You can obtain the rubber cups (p/no.4620ER4002B) from the LG spares dept. ©NOTE- • Proper placement and leveling of the washer will ensure long, regular and reliable operation. •The washer must be 100% horizontal and stand firmly in position. • It must not “Seesaw" across corners under load. • The installation surface must be clean, free from floor wax and other lubricant coatings. • Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur. 16 How to use washer Operating washing machine ►II 1. Sort Laundry. (Refer to 18 page) / / . \ \ / hi \ \ \ In w ▼ 4 ^ / 4. Select a Program. (Refer to 19~21 page) Select options at this time (Refer to 23~28 page) ■ Additional Program ■ Temperature ■ Spin Speed ■ Other functions 6. Press the Start/Pause button. 17 How to use washer 1. Care Labels Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. 2. Sorting To get the best results, sort clothes into loads that can be washed with the same wash cycle. Water temperature and spin speed and different fabrics need to be washed in different ways. Always sort dark colors from pale colors and whites. Wash separately as dye and lint transfer can occur causing discolouration of white etc. If possible, do not wash heavily soiled items with lightly soiled one. • Soil (Heavy, Normal, Light) Separate clothes according to amount of soil. • Color (White, Lights, Darks) Separate white fabrics from colored fabrics. • Lint (Lint producers, Collectors) Wash lint producers and lint collectors separately. 3. Carin...