Votes - 3, Average rating: 3.3 ( )

Manafacture: LG File size: 3.75 mb File name: Language of manual:

Other manuals for this model:

Washers - F1273ND (4.66 mb)

Then tighten the 4 screws. Rubber packing 3. Push the water supply hose vertically upwards so that the rubber packing within in the hose can adhere completely to the tap and then tighten it by screwing it to the right. Normal Tap without thread & one touch type inlet hose 1. Untighten the upper connector screw. Fixing screw ■ In case the diameter of the tap is large remove the guide plate. Guide plate 2. Push the upper connector up 3. till the rubber packing is in tight contact with the tap. Then tighten the 4 screws. Rubber packing k Connect the water supply hose to the middle connector, pushing the plate down. Plate Connector Middle connector •Turn the middle connector not to have water leaked. ■ Make sure that the rubber seal is inside the hose connector. • To separate the water supply hose from the middle connector shut off the tap. Then pull the inlet hose down, pushing the plate down. ■ Your machine comes with only cold water connection. ■ Make sure that there are no kinks in the hose and that it is not crushed. retaliation This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stopcock if the machine is to be left for any length of time (e.g. holiday), especially if there is no floor drain(gully) in the immediate vicinity. When disposing of the appliance, cut off the mains cable, and destroy the plug Disable the door lock to prevent young children being trapped inside. Packaging material (e.g. Films, Styrofoam) can be dangerous for children. There is a risk of suffocation I Keep all packaging well away from children When installing the drain hose sink, secure it tightly with a string. Proper securing of the drain hose will protect the floor from damage due to water leakage. • The drain hose should not be placed higher than 100 cm above the floor. Water in the washer does not drain or drains slowly. • Proper securing of the drain hose will protect the floor from damage due to water leakage. • When the drain hose is too long, do not force back into the washer. This will cause abnormal noise. retaliation ■ Level adjustment 1. Adjusting the washing machine level properly prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room. Timber or suspended type flooring may contribute to excessive vibration and unblance errors. 2. If the floor is uneven, adjust the adjustable feet as required, (do not insert pieces of wood etc. under the feet) Make sure that all four feet are stable and resting on the floor and then check that the appliance is perfectly level, (use a spirit level) SK After the washer is level, tighten the lock nuts up towards of the base of the washer. All lock nuts must be tightened. 'n the case the washing machine is installed on a raised platform, it must be securely fastened in order to eliminate the risk that it might fall off. Diagonal Check When pushing down the edges of the washing machine top plate diagonally, the machine should not move up and down at all. (Please, check both of two directions) If machine rocks when pushing the machine top plate diagonally, adjust the feet again. ■ Concrete floors • The installation surface must be clean, dry and level. • Install washer on a flat hard floor. ■ Tile floors (Slippery floors) • Position each foot on the Tread Mate and level the machine to suit. (Cut Tread Mate into 70x70 mm sections and stick the pieces on to the dry tile where machine is to be placed.) Tread Mate is a self adhesive material used on ladders & steps that prevents slipping. ■ Wooden floors (Suspended floors) •Wooden floors are particularly susceptible to vibration. •To prevent vibration we recommend you place rubber cups under each foot, at least 15mm thick under the washer, secured to at least 2 floor beams with screws. • If possible install the washer in one of the corners of the room, where the floor is more stable. )K Insert the rubber cups to reduce vibration. M You can obtain the rubber cups (plno.4620ER4002B) from the LG spares dept. Important! • Proper placement and levelling of the washer ensure long,regular and reliable operation. • The washer must be absolutely horizontal and stand firmly in position. • It must not “Seesaw” across corners under load. • The installation surface must be clean, free from floor wax and other lubricant coatings. • Do not let the feet of the washer get wet. If feet of the washer get wet, slipping may occur. are before washing Before the first washing Select a cycle (COTTON 60°C, add a half load of detergent) allow the unit to wash without clothing. This will remove residues and water from the drum that may have been left during manufacturing. Caring before washing 1. Care Labels Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed. 2. Sorting To get the b...

Download now

Please, enter two numbers from picture: