Votes - 3, Average rating: 5 ( )

Manafacture: Beko File size: 687.77 kb File name: 05a3a8b5-a383-416b-a54e-137797b1fdae.pdf Language of manual:

COMMON LAUNDRY PROBLEMS (cont’d) Problem Possible Cause Suggested Solution Excessive wrinkling Machine too full Water too hot Permanent press items should be washed in half-loads to prevent wrinkling. If possible, use a slower spin speed. Use lower wash temperature settings. Rips, snags, Sharp objects in pockets Empty all pockets and turn inside out before laundering. excess wear Hooks, snaps, zippers, buckles Harsh chemicals Existing rips and tears Permanent press items Fasten all hooks, snaps, and zippers before laundering to avoid snags. Remove sharp buckles. Turn knits inside out. Before washing, rinse harsh chemicals (such as battery acid, hair care chemicals, cleaning solutions, etc.) from towels and other articles to avoid holes in fabrics. Do not allow these unrinsed items to contact other fabrics. Mend all garments before laundering to prevent enlarging of rips. These items may fray at edges from normal wear, not the washer. Wash only in half loads and don’t wash in the same load with heavy items, such as towels or jeans. . 13 TROUBLESHOOTING Before calling for technical assistance, check that the operations described below have been carried out correctly; this will save both time and money. Does not work/Indicator light is not lit Check that: 1) The On/Off button is pressed in. 2) The plug is correctly inserted in the socket. 3) The main power supply is on. Indicator light is on but unit does not work Check that: 1) The door is closed securely. 2) The On/Off button is pressed in. 3) The programmer knob is on a program. 4) The plug is correctly inserted in the socket. 5) The main power supply is on. 6) See “Does not fill with water” below. Does not fill with water Check that: 1) There is water in the pipes. 2) The tap to the water source is open. 3) The water supply hose is not kinked. 4) The inlet filter between the valve and water feed hose is clean (see page 6). Fills and drains continuously Check that: 1) The drain hose is positioned at the correct height (see page 6). 2) If connected to a sink, the drain hose outlet is not under water. Does not drain and spin Check that: 1) The No Spin button is not pressed in. 2) The drain hose is in the correct position. 3) The drain hose is not kinked. 4) The amount of detergent is not excessive. 5) The detergent dispenser is not encrusted with residue. 6) The detergent is low-sudsing specifically for front-loading washers. Vibrates and is noisy Check that: 1) Large items have not become entangled (sheets, tablecloths, etc.). 2) The machine is level (see page 5). 3) The four packing screws, spacers and two lower rods have been removed (see page 5). The door will not open 1) For safety reasons, the door remains locked for two to three minutes after the program has finished. If you think you have resolved the problem, try starting the machine again. If the problem persists, call for technical assistance (see page 15). BEFORE CALLING FOR SERVICE Before calling for service or contacting AM Appliance Group regarding a warranty issue, be prepared to explain: 1) The appliance model number (shown on the detergent dispenser) 2) The serial number of the machine (located on the inner door facing) 3) The specific problem PRODUCT WARRANTY MODEL EWF272EL Be sure to complete the Warranty Registration Card you received with your appliance and mail it to AM Appliance Group to validate your appliance warranty. Cosmetic damage must be reported to your dealer within five days from the date of purchase. After unpacking the unit, thoroughly check it for cosmetic damage. . ". . !!. From date of purchase. Eurotech replacement parts and/or repair labor to correct defect in materials or workmanship. Service must be provided by an authorized Eurotech service agent. %!#!. From date of purchase. Eurotech replacement parts (labor costs not included) for all parts due to defect in materials or wormkanship. Service must be provided by an authorized Eurotech service agent. &!!#!. From date of purchase. Eurotech replacement parts (labor costs not included) for any defective solid-state controls, timers, motors, or pumps. Replacement of cabinets that may have rusted through. Service must be provided by an authorized Eurotech service agent. ! !!#!. Eurotech replacement parts (labor costs not included) for the stainless steel inner or outer drum if ...

Download now

Please, enter two numbers from picture: