Votes - 2, Average rating: 4
(
)
)
|
manual abstract
Pull out water inlet hoses. Clean top of water inlet valvefilter with a brush. If filters are extremely soiled you canpull it out with a pincer. You can take out flat side of water inlet hoses with its seal and clean with tap water. (2 filters in Single water inlet machines, 4 filters in double water inletmachines) Hose There is risk of freezing in cold region, if your machine isplaced in a cold place remaining water in hoses must bedrained with pump filter when machine is not used. Water inlet hoses can be drained by taking it out from tap. 18 Cleaning Pump Filter There is filter system maintaning long lifetime of pump by blocking foreign objects like button, cloth fiber enter to the pump during drain of washing water. It is useful to clean the filter when it is soiled. In order to this: Unplug your machine. Open the filter at bottom right corner by pressing marked space on the lid. Hot water risk: There might be 15 lt., 90°C hot water in the Caution! drum. Open the filter carefully. Before opening filter drain water with drain hose. Pull out If the filter and hose tap does not fit, it leaks water. drain hose from its place. Prepare a suitable containerand open tap of hose. After water is drained place the tap properly. Open the filter by turning and drain the remaining water (max30ml) to filter tap. Clean remaining foreignobject in the filter. When finished turn in clockwise direction and close. Close the filter tap by pushing. 19 Installation 6 If your system is not ready, let a certified plumber make it 2. Leveling the feet ready. Or order to operate your machine without noise andvibration it must be properly on balance. Four feet of your 1. Removing the transportation locks machine can be adjusted. First loosen plastic counter bolt. Tighten the counter bolt after adjusting the feet for leveling Before the washing machine is operated, the transit bars your machine. must be removed! In order to do this: 1. Loosen “C” bolts by rotating them counter clockwise witha suitable spanner2. Remove transportation locks by turning. 3. Place “P” plastic covers onto the openings of transporta- tion locks by rotating in direction of arrow and pushing. Attention please! Store the transit bars for using whenmachine is to be transported again. Always transport your machine with transportation locks. 3. Water Connections a) Water Inlet Hose Your machine is connected to water supply by special hoses supplied by the machine. Red hose or hose writtenred on it is hot water inlet, blue hose or hose written blueon it is cold water inlet. There plastic seal (4 for double water inlet models, 2for single water inlet models) on hose or plastic bag foreliminating any leakage in connections points. These seals must be used on each side of the connection. Seals on machine side must be connected filter cannal. 20 Connection points are below water pressure there turn on tap water after connection. Check all connections for leaks In order to eliminate any risk due to water leakage keepthe taps off when machine is not used. Your machine will operate efficiently if the water from tap is minimum 1 and maximum 10 bars. Practically 1 bar means8 liters of water in one minute when tap is fully on. Connect dirsekli end to the machine. Tighten bolts with hand power, do not use spanner. Double inlet models can be used with blind cap as a singleinlet machine. Connect blind cap to hot water inlet. Sealmust be for stopping water leakage. Do not connect single inlet machine to hot water. If machine is connected with Y part to a double inlet and over 40.C for single inlet machines, machine may switch toprotection mode. b) Water drain hose Water drain hose could be placed either at the side of the bath tub, or directly to the drain. The hose should not be bent. Water drain hose should be secured with the elbow so that it would not fall down on the ground. The hose should be placed between 40 and 100 cm. fromthe ground. Water drain hose could be placed directly to the drain water inlet. 21 4. Electrical connection Connect the power cord to the appropirate electricalsystem which is being supported by the maximumvoltage and current rating indicated on the rating plateplaced inside the kick plate. Look! Page 1, Steps before operating FullautomaticWashing Machine and safety precautions. Make sure that you have grounded power outlet. Attention! Before any operation of the machine checkthe following. • Did you close the front door? • Is the tap open? • Is water drain hose placed properly? • Is power connected? Helpful tips on stain removal The following.. fabric manufacturer. Alcoholic baverages: Wipe the fabric first with water, then water- glycerine solution and rinse with vinegar-water solution. Shoe polish: Without harming the fabric, remove the stain carefully and grind it with detergent. If this doesn’t help, prepare awater to alcohol solution (2 to 1) and rub the fabric, then wash itwith warm water. Tea and coffee: Pour hot water on to the stain and the...