Votes - 3, Average rating: 3.3
(
)
)
|
manual abstract
Cooktop Front Projects Outward as Shown From Standard Depth Cabinets. Flush With Cabinet Front Cooktop Front Flush With Cabinets - a Minimum of 25-3/4" Cabinet Depth Required 1/2" Above Adjacent Countertops. 26-5/8" 12" 1/2"8-7/16" Countertop Level 22-3/4" 23-1/4" 3" to Center Line of Gas Inlet 2-1/2" Cabinet Face - Projecting Control Panel Cabinet Face - Flush Control Panel 1/2" Low Back 21-1/4" High Back Revised 7/97 This cooktop is factory set for natural gas and has 6 gas burners and a grill. Liquid Propane Gas Model Also Available: ZGU48L6RWSS–6 gas burners and a grill. Installation Options: This cooktop can be installed in standard 24" or deeper 25" cabinets. • In 24" deep cabinets, the front of the cooktop will project approximately 1-7/8" beyond the front of the countertop. • In 25" deep cabinets, the cooktop will be flush with the front of the countertop • The stainless surface of the cooktop will be 1/2" higher than adjacent countertop. Accessory Requirements: All models require the installation of a backguard. A backguard should be ordered at the same time as the cooktop. Both should be on site before cabinetry has been installed. Order one backguard: ZXC1B48WSS–1-1/2" high backguard (required for island installations) ZXC12B48WSS–12" high backguard ZXC22B48WSS–22" high backguard with warming shelf (2 piece) ZXC22B48WSS ZXC12B48WSS ZXC1B48WSS For answers to your Monogram,® GE Profile,™ GE, Hotpoint and RCA appliance questions, call GE Answer Center® service, 800.626.2000. Listed by R UL Underwriters Laboratories Monogram. ™ ZGU48N6RWSS—48" Professional Gas Cooktop Dimensions and Specifications (in inches) 48" Wide Hood 30" Min. 36" Max. 18" Min. 12" Min. to Combustible Material Each Side 36" Min. to Combustible Material From Cooking Surface 13" Max. 17" 22-3/4" Min. Electric/Gas Supply 46-1/8" 7/8" 8" 2-1/2" 2" Cooking Surface Low Back High Shelf 26-5/8" 10"2-1/2" 21-1/4" 12" 36" Min. to Combustibles Island Trim 12" Min. to Combustibles Without Backguard 36" Min. to Combustibles Advance Planning: Refer to dimensional drawings for appropriate placement and necessary clearances when planning the installation. • Cabinetry cannot be installed directly above the cooktop. • This cooktop requires the installation of a vent hood, 30" to 36" above the surface. –The vent hood must be at least 24" deep. –The vent hood must be the same width as the cooktop. –The vent hood blower should provide at least 800 CFM and up to 1200 CFM. –Choose a vent hood with 800CFM for best performance when operating the grill. • Working areas adjacent to the range should have 18" minimum clearance between countertop and cabinet bottom. • Clearance between cooktop and side wall or combustible material must be at least 12" on each side. • This cooktop requires 8" free space below the countertop. • If the cooktop is installed in an island: –Allow 12" min. clearance at the back to combustible materials. –Allow 36" min. above the cooking surface to combustible materials. • Installation must conform with local codes. In the absence of local codes, the gas cooktop must comply with the National Fuel Gas Code, ANSI Z223.1, latest edition. A.G.A. approved For answers to your Monogram,® GE Profile,™ GE, Hotpoint and RCA appliance questions, call GE Answer Center® service, 800.626.2000. Listed by R UL Underwriters Laboratories Revised 7/97 Monogram. ™ ZGU48N6RWSS—48" Professional Gas Cooktop Dimensions and Specifications (in inches) Revised 7/97 8" 2-1/2" 7/8" 46-1/8" 22-3/4" 26-5/8" 8-7/16" 47-7/8" Monogram FRONT REAR HEATING FRONT REAR FRONT REAR Counter Sunk Screws Adjacent Cabinet and Countertop 17" 2" Locate gas inlet on back wall or on floor 2" from back wall 16" Cutting the Countertop Opening: Measure carefully when cutting the countertop. Make sure sides of the opening are parallel. • This Monogram™ gas cooktop is designed to fit in 48" or larger base cabinet. • This cooktop requires 8" free space below the countertop. • The cooktop is designed to hang from the countertop from its side flanges. • Smooth any rough edges on the countertop before installing. –Formica countertop edges must be finished. The countertop must be strong enough to support the weight of the cooktop. • Support cleats can be secured to cabinet sides OR build a support deck or box inside the cabinet which will support the weight of the cooktop. –Build the support box using a solid material, cut a 5" x 5" square in the left rear corner for the gas inlet and power cord clearances. Installation Information: Before installing, consult installation instructions (Pub. No. 49-8812) packed with product for current dimensional data. For answers to your Monogram,® GE Profile,™ GE, Hotpoint and RCA appliance questions, call GE Answer Center® service, 800.626.2000. Listed by R UL Underwriters Laboratories Monogram. ™ ZGU48N6RWSS—48" Professional Gas Cooktop Monogram FRONT REAR FRONT REAR REAR FRONT Features and Benefits • Stainless Steel Model • Natural Gas • 48” Gas Cookto...