Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
• When you have found a UHF channel without interference, do not forget to store it on your TV. The satellite receiver automatically stores the new setting when you press the [menu] button on the remote control. • Disconnect the satellite receiver from the mains. REMEMBER: Please note that a later resetting to factory settings always resets the satellite receiver to the original UHF channel setting on channel 38. We therefore recommend that you make a note of the UHF channel that you change your satellite receiver to use here to your left to enable you to make the same setting again after a resetting without having to experiment first. ($ ! Connect your VCR via a SCART cable to the SCART connector marked VCR on the satellite receiver. At playback VCRs normally send a switch signal to the satellite receiver via the SCART cable. Thus the VCR signal is automatically transmitted to the TV where it is displayed on the screen. If your VCR does not send this switch signal, you can switch by means of the [EXT] button of the remote control. ($& !4 If you have a Super VHS VCR, you can make Super VHS quality recordings from your digital satellite receiver. See sections 4.3.2 and 4.3.3 for information on how to set the signal type of the two SCART connectors (RGB, Composite video and S-VHS) (, 4/ * (,& To get the optimum sound quality you can connect the satellite receiver to a Hi-fi amplifier. To do this you must connect the Audio R and Audio L connectors at the back of the satellite receiver with a suitable cable to the corresponding input on your Hi-fi amplifier (e.g. AUX, TAPE1 or TAPE2). VCR connection Analog audio UHF transmitter channel chosen: _________ TRIAX DVB 75SI 14 (,( 5)6 If your Hi-fi amplifier has a digital audio input, you can connect the AUDIO OUT DIGITAL connector to the digital audio input on your amplifier. Available sample frequencies: 16, 22.05, 24, 32, 44.1 and 48 KHz. NOTE: If you receive a satellite channel transmitting full AC3 digital sound, you must choose the AC3 audio channel via the [A/B] button on the remote control and the corresponding screen menu. When the AC3 audio channel has been selected, the sound is exclusively transmitted from the digital audio output of the satellite receiver (See also chapter 4.4.4). (#. ()( The RS232 connector can be used for linking the satellite receiver with the serial COM port of a PC. A so-called ’straight through’ serial cable must be used (pin-1-to-pin-1, pin-2-to-pin-2, etc.). From Triax’ home page (you can download e.g. new software for updating the satellite receiver system software via a PC programme (e.g. HyperTerm). For this purpose you have to use the serial number of your receiver. The system software can also be updated via satellite without use of a PC. (7 ** The DVB 75SI has an integrated telephone modem. You must connect the satellite receiver modem connector via the supplied telephone cable (10 m) to the nearest telephone socket in your house. If the cable is too short, extension cables and connection boxes are available from your teleshop. Often the connection can be made via the small RJ-11 connector in the supplied cable which fits into the ’phone’ connection of a number identifier, answer phone or fax. Alternatively, you can go to the teleshop to buy an adapter which fits into the wall socket of your telephone connection. The modem connection of the satellite receiver requires connection to a normal telephone line. If you have an ISDN installation, you can only connect the model to the telephone line if you have an A/B or TA adapter which gives a normal analog telephone signal. An ISDN modem usually features such an adapter or it can be bought separately in your teleshop. Digital audio Modem connection via wall socket Modem connection via number indicator TRIAX DVB 75 SI 15 The modem is automatically used by the satellite receiver when you receive interactive services requiring a return channel. It is also used when you want to buy services such as IPPV (Impulse-Pay-Per- View, e.g. KIOSK and pay movies). When you have accepted to by the programme in question, the modem automatically dials up the telephone number stored on the smart card, contacts the administration computer of the programme provider and debits your account. NOTE: This function will only work if the modem connection of your satellite receiver is connected to a telephone line, and only if the line is free (not busy). Moreover, a modem call in progress will automatically be interrupted if you lift the receiver of your telephone to make a normal telephone call. In that case you will have to repeat the order or try again later. (8 If you have followed the above instructions carefully, you simply connect the satellite receiver mains plug to the wall socket and switch the receiver on by means of the red On/Standby button on the remote control. With your Triax DVB 75SI satellite receiver you can no...
Other models in this manual:Satellite Receivers - DVB 75SI (1.73 mb)