Votes - 1, Average rating: 3 ( )

Manafacture: Humax File size: 3.22 mb File name: Language of manual:

2. Connect DiSEqC 1.2 Please refer to page GB39. The Locking Time might take longer than expected during the initial boot if the motorised system is set .enable. mode. 3. Connect a Satellite antenna To the digital receiver, you can connect either a single satellite antenna directly or through converter box several antennas or LNB of multi-feed equipment. You can connect a further Sat-receiver(for example analogue), with the receiver of common antenna equipment that has satellite signals. 4. Loop Through If you have another analogue or digital STB and you wish to use the same LNB then you can connect it via the loop through. Connect one end of a Coaxial cable to the LNB OUT on the STB and connect the other end to the LNB IN on your second STB. . F1-FOX models are not applicable. GB4 Reference 5. Software Upgrade HUMAX digital set-top box is a highly sophisticated product - incorporating one of the best software applications. Whenever a problem is found with this software or, in fact, extra functions or enhanced applications are added, the software in the equipment has to be upgraded. In order to maintain proper performance of the product, it is essential to have the most up to date software. The latest news and release of software versions may be found at HUMAX website - It is recommended that users register to HCSA(HUMAX Customer Service Area) and periodically check for the availability of software upgrade. There are three methods to upgrade the software: (a) set-top box to set-top box download(copies the software of the main unit into slave unit); (b) pc to set-top box download(downloads the software directly from pc to the model requiring upgrade); (c) OTA over-the-air(downloads the software where the manufacturer reserves the right to decide when and where to release through satellite system). Over The Air(OTA) is simply another alternative for downloading software versions. However, the manufacturer reserves the right to decide when and where this software upgrade can take place by "beaming" latest software versions over the air via satellite systems. Note that OTA is only limited to certain geographical regions mainly due to different satellites having different footprints(area where the signal can be received). SUSS(TM) is an official trademark and logo for HUMAX loader software to perform OTA. The software upgrade via satellite system will only occur under the following circumstances: 1) the equipment should have appropriate loader software; 2) the manufacturer decides to release software downloading via a designated satellite system; 3) the equipment must be "tuned" properly to the same satellite that the manufacturer uses. • Note : CR-FOX complies with the OTA type of CryptoWorks. GB5 STB Connections Front Panel F1-FOX Free-To-Air VA-FOX 1 Smart card CR-FOX 1 Smart card GB6 STB Connections Front Panel NA-FOX 1 Smart card • , Press to change services down and up. . SMART CARD SLOT Insert a smart card in the slot with the gold chip facing up. Otherwise, it will not operate properly. . ERROR LED(AMBER) Indicates that the STB has an error. . STANDBY LED(RED) Indicates that the STB is under standby. . OPERATING LED(GREEN) Indicates that the STB is operating. . TV/RADIO Press to switch between TV and Radio modes. . STANDBY Press to switch between Operation and Standby modes. GB7 Rear Panel F1-FOX VA-FOX, CR-FOX, NA-FOX . LNB IN Use to connect an antenna. . LNB OUT Use it when connecting to another STB. . RS-232C Use it when connecting to your PC. . TV SCART For the audio/video input of the TV. . VCR SCART For the VCR. . AUDIO OUTPUT Audio signal from your STB to Hi-Fi system. GB8 STB Connections There are several ways of connecting the STB to your existing Audio/TV system. We recommend using one of the following set-up for best results: • The specifications of Rear panel are based on VA-FOX. TV only 1. Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV. 2. Connect the coaxial cable from the LNB to the LNB IN socket on the STB. TV with VCR 1. Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV. 2. Connect one end of a 21-pin SCART cable to the VCR SCART connector on the STB and the other end to a SCART socket on your VCR. 3. Connect the coaxial cable from the LNB to the LNB IN socket on the STB. With Hi-Fi System 1. Connect an RCA/Cinch stereo cable from the AUDIO L,R sockets on the back of the STB to the LINE, AUX, SPARE OR EXTRA input sockets on your Hi-Fi system. GB9 • The specifications of Rear panel are based on VA-FOX. TV with VCR and Motorised System(DiSEqC 1.2) 1. Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB and the other end to a SCART socket on your TV. 2. Connect one end of a 21-pin SCART cable to the VCR SCART connector on the STB and the other end to a SCART socket on your VCR. 3. Connect t...

Download now

Please, enter two numbers from picture: