Votes - 3, Average rating: 3 ( )

Manafacture: Winegard File size: 2.2 mb File name: bf0795fd-36e6-44ac-adf0-17416542dba7.pdf Language of manual:

46 cm (18") Antenna height..................................... 53 cm Antenna width ...................................... 49 cm Gain at mid-range 11.2 GHz..............................33.22 dBi 12.1 GHz..............................33.89 dBi 12.6 GHz..............................34.23 dBi Effective aperture................................. 46 cm Aperture efficiency .................................. 73% Cross polarization (on axis)... ..............-21 dB Beamwidth at -3 dB ................................. 3.5o Beamwidth at -10 dB ............................... 7.00 F/D Ratio ................................................. 0.59 Frequency Range ................10.95-12.75GHz Offset angle............................................... 240 Gauge .................. 22 gauge galvanized steel Finish: ........ Textured thermoset powder coat Electronics Specifications Primary Power .............................+13.8 VDC Power Consumption ..........................3 amps Operating Temperature ......... -10° to +130°F Humidity ....................... 90% noncondensing Size .................. 4-1/2"W x 4-1/4"H x 1-3/4"D Weight.....................................................1 lb. Mount Specifications Height Lowered .......................................... 8" Height Raised .....................30" vertical max. Roof space required ..........40"L x 20"W min. Turning diameter clearance ..................... 33” Antenna Movement................... 2 DC motors Weight ................................................. 16 lbs. Shipping Weight..................................20 lbs. Carton ......... 27-3/4"L x 20-3/8"W x 10-3/4"D 10 11 Installation requirements FIGURE 1 FIGURE 3 To install the Winegard Automatic Digital Satellite Dish, check with your RV dealer or manufacturer. Your RV may already be pre-wired for this system, and/or may have a reinforced roof area available. 1. Choose a location on the roof that will allow the dish to raise and rotate without interference from other roof-mounted equipment. 2. Roof space required for operation is 40”L x 20”W minimum. Refer to Figures 1, 2, 3 and 5 for operating parameters. 3. The unit must be level for best operation. The unit may be up to 2.5° off level. For the fastest, most reliable operation, it should be as close to level as possible. Use the hydraulic or manual leveling equipment on your vehicle to level the roof as much as possible. Before beginning installation: If the mounting area is not level, you can use a roof wedge, Figure 4. Winegard’s RW-5000 roof wedge corrects tilt up to 3.7°. For units with severely sloping roofs, more than one wedge may be needed. If the roof wedge is too thick, use stainless or aluminum washers. 4. When choosing a location for the interior wall plate control panel, consider wiring, ease of viewing wall plate and distance from your television set. FIGURE 2 FIGURE 4 FIGURE 5 33” DIAMETER TURNING 28” FRONT OF VEHICLE CENTER ROOF LINE 29.9” 8.00” 40.55” 27.8” 12.75” Rotate Axis RW-5000 ROOF WEDGE & GASKET VEHICLE ROOF 27.80 19.18 19.18” 27.80” 12 FIGURE 6 CENTER LINE OF COACH ROOF The length of this cable MUST BE 53 inches from back of electronics housing to clamp. NO CLAMPS ALONG THIS 53” LENGTH! FRONT OF VEHICLE The length of this cable MUST BE 53 inches from back of electronics housing to clamp. NO CLAMPS ALONG THIS 53” LENGTH! FRONT OF VEHICLE 4” MINIMUM from first clamp to cable-entry plate First cable clamp here! Cable-entry plate DRIVER SIDE PASSENGER SIDE 20” FIGURE 6A FIGURE 6B FRONT OF VEHICLE CENTER LINE OF COACH ROOF 20” The length of this cable MUST BE 53 inches from back of electronics housing to clamp. NO CLAMPS ALONG THIS 53” LENGTH! First cable clamp here! Cable clamps every 12” from first cable clamp 4” DRIVER SIDE PASSENGER SIDE First cable clamp here! CENTER LINE OF COACH ROOF DRIVER SIDE PASSENGER SIDE Cable-entry plate Cable-entry plate Cable-entry plate Cable clamps every 12” from first cable clamp Cable-entry plate 20” before putting under cable-entry plate. Electrical tape, wrapped at cut line. before putting under cable-entry plate. Electrical tape, wrapped at cut line. n 1. Position the roof template on the vehicle roof and drill 1/8” holes for the screws. DO NOT drill clear through into interior of vehicle. The screws fasten mount to the roof only. Be sure the roof can securely hold system. 2. Place base plate gasket under the base before screwing unit down. Secure the base plate of the motorized assembly to the roof using appropriate screws. DO NOT APPLY SEALANT AT THIS TIME. Note: IF YOU ARE USING THE ROOF WEDGE (RW-5000), use the 3/16” gasket included with motorized mount under the roof wedge. Install 1/16” gasket included with the RW-5000 roof wedge between mount and roof wedge. Longer screws are needed for installation when using roof wedge. 4. Partially unroll your bundled cable and gently remove any kinks. CAUTION!! See illustrations on page 12. Cable MUST BE ROUTED AS SHOWN IN FIGURE 6, 6A, and 6...

Download now

Please, enter two numbers from picture: