Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
If the interference goes away, it was probably caused by your pager. To eliminate the interference, move the pager away from the affected device. If the interference cannot be eliminated, the FCC requires that you stop using your pager. Modifying or tampering with your pager’s internal components can cause a malfunction and void your FCC authorization to operate it. If your pager is not performing as it should, contact your pager service. This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause any harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation. Clearvue. is a proprietary trademark of Uniden America Corporation. ©1998 Uniden America Corporation All rights reserved. Printed in the Philippines Contents Important.......................1 Introduction .....................2 UsingthisOwnersGuide ...............2 InstallingtheBattery .................3 TurningYourPagerOn................4 LowBatteryWarning.................4 Controls .......................5 StandbyDisplay....................6 ClearvueIlluminatedDisplay .............7 Receiving and Displaying Personal Messages ......8 TheFunctionMenu..................9 MailDropHistory..................16 UsingThePhoneDirectory .............18 TheSetupOptionsMenu...............21 Important Your pager is capable of storing messages and telephone numbers totaling up to 100,000 characters. To prevent the loss of important data due to battery failure, replace the battery before the power level becomes too low. Battery life will vary depending on several factors, including: . The amount of time the Clearvue illuminated display is active. . The amount of time the pager is “ON.” Introduction Congratulations on your purchase of the ALP9094 four line alpha/numeric pager. This compact, state-of-the-art pager has many features, including: . 20 Folder Locations for Mail Drops . 40 Personal Message Locations . Clearvue Illuminated Display . Multiple Alert Tones . Silent or Vibrating Alerts . Time and Date Alarms . Out-of-Range Indicator . Phone Directory To ensure that you understand all of your pager’s features and capabilities, please read this owners manual carefully before you use your pager. Visit our internet site at: Using this Owners Guide . When you see the word “press,” press and release the specified key. If needed to “press and hold,” you will be prompted to do so. . The displays in this owners manual are general representations of what you will see. Your paging service provider may change the wording. Installing the Battery Your pager requires one 1.5 VDC, AAA battery for power. Caution: Only use the battery specified above. 1. Release the battery compartment lock.Slide and lift off the battery cover. 2. Insert the AAA battery into the compartment according to the polarity symbols (+) and (–) marked inside. 3. Match the dots on the pager and battery cover. Slide the battery cover on, then slide the lock-tab down. Turning Your Pager On Press and hold N for approximately two seconds. The display will temporarily go blank and then show the standby display (see page 6). Turning Your Pager Off 1. At the standby display, press N to go the Function menu (page 9). 2. Press > to select POWER OFF (). 3. Press N again and your pager is in the standby mode. Low Battery Warning When battery power is low, this symbol ( ) appears in the bottom center of the display, and – once every 30 minutes – a low beep sounds that lasts four seconds. When this happens: l Replace the battery as soon as possible to prevent data loss. . You will have to press N twice (instead of normally pressing once) at the Standby display to go to the Function menu (page 9). The built-in memory saver will store messages and settings for approximately two minutes while you NOTE change the battery -or after the battery loses power. Controls 1. Backward Menu/Page Scroll Key (<) 2. Forward Menu/Page Scroll Key (>) 3. Enter Key (N) 4. Speaker 5. Scroll Down Key (t) 6. Display (see next page) 7. Scroll Up Key (s) 8. Strap attachment Standby Display 1. Time 2. Message Status -Displays CALL, MAIL, Low Battery , and FULL. This symbol (-----) indicates no messages or calls. This symbol ( ) indicates all messages have been read. 3. Alarm ( ) -Indicates an alarm has been set. 4. Audio Alert ( ) -This displays when a tone has been selected for message alert. The Silent Alert ( ) and Vibrate ( ) icons are also displayed here. 5. Signal Meter Strength ( ) -Flashes when there is no signal. 6. Carrier Logo -The logo of the assigned carrier is displayed here. Clearvue Illuminated Display Your pager is equipped with the Clearvue illuminated display. To activate this display, perform the following steps: 1. With your pager on, push and hold any key (<, >, s, t,or N) for two seconds. 2. The backlight illuminates and remains on for approximately 20 seconds. ...