P.O. BOX 368023 CLEVELAND, OHIO 44136-9722 45” Snow Thrower Model 1345 SWE PRINTED IN U.S.A. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forestcovered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California

Fold fastener back and under the side chain as pictured below. You will probably need pliers to do it. Once both fasteners are connected, chain assembly must be snug on tire. Advance fasteners on each side chain the same number of links until chain is sufficiently and evenly tight on tire. See front cover picture for proper chain fit. Remove or tie down all unused links once chain is satisfactorily tight. 5 Repeat previous steps for other tire. To get maximum wear and years of use from your

The belt brake should move outward and lift the front auger drive belt from the front auger pulley. • Place new belts on the two auger pulleys making sure that the front auger belt is under the belt brake. Route belts under and to the left of the flat idler pulley. Hold the belts upward in this position. Figure 15 • While lifting up on the handles, bring the frame assembly close to the auger housing and place the two belts on the front and rear engine pulleys. See Figure 16. Figure 16 • Level th

• Connect power cord to switch box on engine. Plug the other end of power cord into a three-hole, grounded 120 volt AC receptacle. • Push starter button on top of the engine to crank engine. As you crank the engine, move choke knob to FULL choke position. • When engine starts, release starter button, and move choke gradually to OFF. If engine falters, move choke immediately to FULL and then gradually to OFF. • When disconnecting the power cord, always unplug from the three-prong receptacle first

Carburetor not adjusted properly. Loss of power 1. Connect and tighten spark plug wire. 2. Remove ice and snow from gas cap. Be certain vent hole is clear. 3. Contact Service Center. 1. Spark plug wire loose. 2. Gas cap vent hole plugged. 3. Exhaust port plugged. Unit fails to propel itself 1. Adjust drive control cable. Refer to “Adjustments”. 2. Replace drive belt. 1. Drive control cable in need of adjustment. 2. Drive belt loose or damaged. Excessive Vibration 1. Loose parts or damaged auger.

Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered 700-xxxx, is painted Cub Yellow, the part number to order would be 700-xxxx-0498. Cub Yellow: 0498 Cub Beige: 0499 Powder Black: 0637 17 Model 1333SWE 8 18 Model 1333SWE Ref. No. Part No. Description Qty. Ref. No. Part No. Description Qty. 1 736-0159 Flat Washer .344 ID x .875 OD 7 72 741-0184 Thrust Bearing .88 ID x 1.44 OD x 1 2 710-3015 Truss. Hd. Mach. Scr.

Ignition Key The ignition key is a safety devise. It must be fully inserted in order for the engine to start. Remove the ignition key when the snow thrower is not in use. Important: Do not turn the ignition key in an attempt to start the engine. Doing so may cause it to break. Figure 4-1 Drive Control Headlight Oil Fill Fuel Cap Primer Choke Ignition Key Oil Drain Starter Button Electric Starter Outlet Recoil Starter Handle Chute Assembly Clean-Out Tool Auger Control Shift Lever Two-Way Chute Co

60 Ottawa Street South, KITCHENER, ONTARIO N2G 4J1 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION OPERATOR’S MANUAL 06/10/08 769-04103 28”, 30”, 33” & 45” Two-Stage Snow Throwers This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare and maintain the unit for best performance. Please read and understand what it says. Table of Contents Safety Symbols................................................... 3 Maintaining Your Sn

714-0143 Clik Pin 3. 784-5687A Auger Clutch Cable Bracket 27. 684-0042C Friction Wheel Assembly 4. 756-0625 Cable Roller 28. 656-0012A Friction Wheel Disc 5. 738-0924 Shoulder Screw 1/4-28 x .375 29. 684-0013B Wheel Shift Rod Assembly 6. 784-5630A Frame Assembly 30. 746-0897 Drive Cable 7. 741-0563 Ball Bearing 31. 748-0190 Spacer 8. 736-0105 Bell Washer 32. 684-0021 Friction Wheel Bracket Ass’y 9. 712-0116 Lock Jam Nut, 3/8-24 33. 732-0264 Extension Spring 10. 741-0598 Hex Flange Bearing 34. 71

If the engine falters, quickly rotate the choke control back toward FULL choke, and then slowly into the OFF position again. 6. When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower. Recoil Starter 1. Rotate choke control to FULL choke position (cold engine start). NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL. 2. Push the primer two or three times for col