Place the pivot pin through the blade assembly bracket and push bar. Position the push bar under the tractor front axel and attach it to the axel using two pins and spring clips. Attach the spring end of the lift rod to the push bar assembly and the other end to the tractor lift arm using two spring clips. OPERATION Alternate holes are provided to permit adjustment of the shoe assemblies for raising or lowering the blade when cleaning gravel drives or walks. When cleaning concrete it is desira

16 x 1" 4 720002 7 Lock Washer, 3/S" 5 717003 7 Hex Nut, Full 3/8"-16 6 107106 2 Shoe Assy. 7 719001 4 Flat Washer, 3/S” 8 720002 4 Lock Washer, 3/8" 9 705004 4 Hex. Cap Screw, 174054 S/8'J-16 x 3/4" 10 1 Pivot Frame Assy. 11 715100 2 Hex Capscrew, l/2”-13 x 1-1/2" 12 717518 2 Hex Nut, 1/2"* 13 13 107116 1 Pivot Plate Assy. 14 722006 2 Cotter Pin 1/8“ x 1" 15 107118 1 Pivot Rod 16 722001 2 Cotter Pin, 3/32” x 3/4" 17 107119 1 Pivot Arm id 156150 1 Spacer 19 705007 1 Hex Capsc

4 Frame, Belt Guard, Idler Assembly. Pan & Supports ENGINE GROUP ......................................................................... 6 Engine, Pulley, V-Belt, Key Switch WHEEL GROUP .......................................................................... 7 Wheels, Axle AUGER DRIVE GROUP ................................................................... 8 Augers, Flite, Gear Case Assembly, Jmpeller & Pulley AUGER HOUSING & CHUTE GROUP .............................................

1687394 Instructions Kit Contents: Ref Part No. Qty. Description 1 1733057 1 Chute Warning Decal 2 1716532 1 Auger Warning Decal 3 1734499 1 Dash Panel Decal 4 1733526 1 Lube Required Decal 5 725432 1 Belt Stretch Decal This kit contains the decals and modifications necessary to convert an export CE snowthrower into an ANSI compliant domestic product. INSTALLATION 1. Remove the push nuts (B, Figure 1) securing the chute wireform (A). 2. Remove and discard the wireform (A). 3. Repl

4 FRAME, HANDLE * SHROUD GROUP (Mfg. No. 1691405 & 1691406) ....................... 8 ENGINE & DRIVE GROUP .....................................-..........................10 DECAL GROUP .......................................................................... 12 STANDARD HARDWARE TORQUE SPECIFICATION ....................... Inside Back Cover Simplicity Housing <5 impeller Group Spring № bo assembled on pins and tiqhl against housing. Hand lighten against spacer (Ref. No. 5). Torque nol

SNOWTHROWER MANUAL START MFG. NO. 1690Э01 MFG. NO. 1691405 3 H.P. SNOWTHROWER ELECTRIC START MFG. NO. 1690902 MFG. NO. 1691406 !imphdtu Product Identification: When ordering parts, keep your products serial number and manufacturer’s number in mind. Variations may occur in a part between early and later model products, causing the product serial number to be listed in the parts description whenever these variations occur. Record your I.D. numbers here for quick, future reference. Product Mf

lbs. {2 places) Hook spring in slot. Belt Stops (Ref. No. 12 & 13) to be 1/16" to 1/16" over belt v.'»1M idler engaged. 10 Spring lo be hooked closed at assembly. Torque ilems 13, 36 & 42 105-130 in. lbs. /23 \ Torquo to 65-75 in. tbs. NOTE: U&e standard hardware torque spec. 17329Q unless otherwise noted. Torque lo 26 in. lbs. {■1 plRCM) AH Models Engine <5 Drive Group Simplicity Ref. Ho. Part. No. Qty. Description 1 1916964 1 LOCKWASHER, 1/4 2 1929486 1 CAPSCREW. Hex Hd.. 1/4-

1/4 pages 8 & 7. 5 Simplicity Frame. Handle & Shroud Group T 76 Tighten nut (Raf. No. iß) 3 It lbs. max. Clutch lever must pivot frcoly. NOT£ U*e standard hardware torque spec. 173209 unless otherwise noted. A*fe to bottom out In palnut (Ref. No. 23). Mfg. No. 1690901 Ä 1690902 Frame. Handle & Shroud Group Simplicity Ref. No. Part No. Qty. Description 31 1664804 1 SWITCH, Ignition 32 916906 1 LOCKWASHER, Int Tooth. 5/8 33 933741 NUT. Speed, "U", #10 34 1664817 1 GUIDE. Choke K

1687391 Instructions Kit Contents: Ref Part No. Qty. Description 1 1733057/7071880 1 Chute Warning Decal 2 1716532 1 Auger Warning Decal 3 1727020 1 Dash Panel Decal 4 1726946 1 Dash Panel Decal This kit contains the decals and modifications necessary to convert an export CE snowthrower into an ANSI compliant domestic product. INSTALLATION 1. Remove the push nuts (B, Figure 1) securing the chute wireform (A). 2. Remove and discard the wireform (A). 3. Replace the icon-based CE de

1687395 Instructions Kit Contents: Ref Part No. Qty. Description 1 1733057 1 Chute Warning Decal 2 1716532 1 Auger Warning Decal 3 1733056 1 Dash Panel Decal 4 725432 1 Belt Stretch Decal 5 728183 1 Friction Disk Decal This kit contains the decals and modifications necessary to convert an export CE snowthrower into an ANSI compliant domestic product. INSTALLATION 1. Remove the push nuts (B, Figure 1) securing the chute wireform (A). 2. Remove and discard the wireform (A). 3. Repla