This washer has an i/2’ O.D. and a hole in the middle slightly smaller than i/16” I.D. 1. Remove the upper left-hand panel from the tractor to expose the valve (A, figure 1). 2. Notice there are two elbows on the side. Disconnect the hose (B) from the front elbow (C). Remove the elbow. 3. Place the washer so it is fully seated inthe hole. 4: Reinstall the elbow (C) and then connect the hose (B). Tighten the nut securely after elbow is properly positioned. Note: Flow reduction washer can be left

No. 1692243 Hitch Mfg. No. 1692244 HEX CAPSCREW CARRIAGE BOLT 0 PLAIN @ WASHER @ LOCKWASHER @ NUT HEX CAPSCREW IDENTlFlCATlON Shown below are actual size heads for standard screw sizes. Example: a l/4 screw has 7/16 head and thus requires a 7/16 wrench. To measure length, use the scale below. 00000 3lV Head 5/s” Head 9/16” Head l/2” Head 7/l 6” Head screw with screw with screw with screw with screw with l/2” SD. 7ll6’S.D. 318” SD. 5/16” SD. 114” S.D. WASHER AND NUT IDENTIFICATION Place the washe

F001019M 04/27/99 IB! ! Table of Contents 2 Warranty 2 Safety Rules 2-4 Contents of Shipping Carton 4 Assembly 5 Operation 6-10 Maintenance 11 kvAv/_,1| Ir.,_ _ LIMITED TWO-YEAR WARRANTY Service and Adjustments 12-15 Storage 16 Troubleshooting 17 Snow Repair Parts 18-24 Engine Repair Parts 25-29 Spanish(EspaSol) 30-46 Parts Ordering/Service Back Cover | ik"J _ir.,_li_ivllq_| I ON CRAFTSMAN SNOW THROWER For two years from the date of purchase, when this Craftsman Snow Thrower is maintained, lubri

1-3/8-16 x 2 In. Hex Head Bolt ©© 1 _/8 In. 1 -3/8 In. Lockwasher Flatwasher 1-3/8 In. Hex Nut @© 2 -3/8-16 Hex Jam Nuts 1 -Starter Motor Cord 2-Shifter Knobs 4 Parts packed separately in carton (not shown full size) 2 -Ignition Keys (Attached to engine in plastic bag) Z_ CAUTION: Always wear safety glasses or eye shields while assembling snow thrower, TOOLS REQUIRED FOR ASSEMBLY 1 -Knife to cut carton and plastic ties 2 -1/2 inch wrenches (or adjustable wrenches) 2-9/16 inch wrenches (or adjust

AugerDrive TractionDrive Spring(Short ,_ Spring(Long) _ I' ' --Figure9 CONNECT REMOTE CHUTE 1. Push remote chute control lever into "Chute Deflector Up" position. 2. Feed "Z" fitting through hole in remote chute bracket. See. 3. Snap remote chute control cable into remote chute bracket. See. 4. Connect "Z" fitting into remote chute control bracket. See. 5. Push remote chute control lever into "Chute Deflector Down" position. 6. Cut tie strap on chute deflector. See Figure. SPEED SELECT LEVER 1.

WARNING Auger must NOT rotate unless the Auger Control lever has been depressed. Proper Auger Drive Belt adjustments stop the auger within 5 seconds after the Auger Control is disengaged. Checking Auger Belt & Belt Guide Adjustments 1. Insert the Engine Key and start the Snowthrower. 2. Engage and disengage the Auger Control a series of ten times, checking that the auger comes to a complete stop within 5 seconds after the control is disengaged each time. 3. If the auger comes to a complete stop

* Cover—on pre-printed two-tone “Swash” stock. Press: * Body—1-color, 2-sided * Cover imprint —1-color, 1-sided Bindery: * Saddle Stitch, Face Trim, 3-Hole Drill * Face Trim COVERS: * This file contains several manuals, which differ only in their covers. * Covers are all present at the beginning of this file. * Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover. • Check the front cover for the individual part number (typically a 171xxxx number). BODY: • The body of

• Adjust snow discharge angle for safe flow when operating near glass enclosures, automobiles, window wells, dropoffs, etc. • Do not overload machine capacity by clearing snow at too fast a ground speed. • Never operate machine at high transport speeds on slippery surfaces. Use care when backing up. • Disengage Auger Control when transporting or not in use. • Never operate the snowthrower without good visibility or light. Always be sure of your footing. • Do not change the engine governor settin

All Rights Reserved. Printed In USA. TP 100-2062-03-IW-S 1 Safety Rules WARNING WARNING This unit is a “two-stage” snowthrower. The first stage is the auger, which feeds the snow back into the impeller housing. The second stage is the impeller, which throws the snow out the discharge chute. If bodily contact is made with the auger or impeller when they are rotating, severe personal injury will occur. To avoid injury, keep others and yourself away from the auger and the discharge chute whenever t

Figure 3. Engine Controls A EF C D G B * A. Electric Start Button C. Starter Handle (On some units only) D. Primer Button B. Fuel Valve E. Throttle Lever *7 HP Engine- Lower F. Engine Key Front Gas Tank Area *5 HP Engine- Lower G. Choke Knob Rear Gas Tank Area 6 Controls GROUND SPEED CONTROLS A. Speed Selector - This lever (A, Figures 4 & 5) is used to set the ground speed of the snowthrower. The snowthrower has five forward speeds, 1–5, and two reverse speeds, 1–2. No neutral position or gate i