Votes - , Average rating: ( )

User manual Bolens, model C Style

Manafacture: Bolens
File size: 5.2 mb
File name: c9a29521-2a0a-0f44-99a9-d40e0b45b8c0.pdf

Language of manual:

The document is loading, please wait

Download nowClose

The document is loading, please wait

Download nowClose

Pulling the starter rope will produce a loud clattering sound, which is not harmful to engine. 2. Move throttle control to STOP position. 3. Remove the ignition key and store in a safe place. 4. Wipe all snow and moisture from the area around the engine as well as the area in and around the drive control and auger control. Also, engage and release both controls several times. Chute Clean-Out ToolThe chute clean-out tool is conveniently fastened to the rear of the auger housing with a mounting clip. Should snow and ice become lodged in the chute assembly during operation, proceed as follows to safely clean the chute assembly and chute opening: 1. Release both the Auger Control and the Drive Control. 2. Stop the engine by removing the ignition key. 3. Remove the clean-out tool from the clip which secures it to the rear of the auger housing. 4. Use the shovel-shaped end of the clean-out tool to dislodge and scoop any snow and ice which has formed in and near the chute assembly. 5. Refasten the clean-out tool to the mounting clip on the rear of the auger housing, reinsert the ignition key and start the snow thrower’s engine. 6. While standing in the operator’s position (behind the snow thrower), engage the auger control for a few seconds to clear any remaining snow and ice from the chute assembly. To Engage Drive1. With the throttle control in the Fast (rabbit) position, move shift lever into one of the six forward (F) positions or two reverse (R) positions. Select a speed appropriate for the snow conditions and a pace you’re comfortable with. 2. Squeeze the auger control against the handle and the augers will turn. Release it and the augers will stop. 3. Squeeze the drive control against the handle the snow thrower will move. Release it and drive motion will stop. To Engage Augers 1. To engage the augers and start throwing snow, squeeze the auger control against the left handle. Release to stop the augers. Auger Control TestPerform the following test before operating your snow thrower for the first time and at the start of each winter. Check the adjustment of the auger control as follows: 1. When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight. 2. In a well-ventilated area, start the snow thrower engine as instructed on the previous page. Make sure the throttle is set in the FAST position. 3. While standing in the operator’s position (behind the snow thrower), engage the auger. 4. Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times. 5. With the throttle control in the FAST (rabbit) position and the auger control in the disengaged “up” position, walk to the front of the machine. 6. Confirm that the auger has completely stopped rotating and shows NO signs of motion. If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control. 7. To readjust the control cable, loosen the upper hex nut on the auger cable bracket. 8. Position the bracket upward to provide more slack (or downward to increase cable tension). See Figure 2.9. Retighten the upper hex nut. 10. Repeat Auger Control Test to verify proper adjust- ment has been achieved. Figure 2When selecting a Drive Speed, use the slower speeds until you are comfortable and familiar with the operation of the snow thrower. NEVER reposition the shift lever (change speeds or direction of travel) without first releasing the drive control and bringing the snow thrower to a complete stop. Doing so will result in premature wear to the snow thrower’s drive system. WARNINGNever use your hands to clean snow and ice from the chute assembly or auger housing. The muffler, engine and surrounding areas become hot and can cause a burn. Do not touch. 11 12 5 Making Adjustments Auger Control Refer to Auger Control Test on Page 11 to adjust the auger control. Drive Control When the drive control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight. Check the adjustment of the drive control as follows: 1. With the drive control released, push the snow thrower gently forward. The unit should roll freely. 2. Engage the drive control and gently attempt to push the snow thrower forward. The wheels should not turn. The unit should not roll freely. 3. With the drive control released, move the shift lever back and forth between the R2 position and the F6 position several times. There should be no resistance in the shift lever. 4. If any of the above tests failed, the drive cable is in need of adjustment. Proceed as follows: 5. Loosen the lower hex nut on the drive cable bracket. See Figure 3. 6. Position the bracket upward to provide more slack (or downward to increase cable tension). 7. Retighten the upper hex nut. Chute Assembly The distance snow is thrown ...