Votes - , Average rating:
(
)
)
Manafacture: Cub Cadet
File size: 5.35 mb
File name: 5e3e402e-a784-b094-3d22-8f3713cfc582.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
• Connect power cord to switch box on engine. Plug the other end of power cord into a three-hole, grounded 120 volt AC receptacle. • Push starter button on top of the engine to crank engine. As you crank the engine, move choke knob to FULL choke position. • When engine starts, release starter button, and move choke gradually to OFF. If engine falters, move choke immediately to FULL and then gradually to OFF. • When disconnecting the power cord, always unplug from the three-prong receptacle first and then from the snow thrower. Recoil Starter • Rotate choke knob to FULL choke position (cold engine start). If engine is warm, place choke in OFF position instead of FULL. • Push primer button two or three times. If engine is warm, push primer button once only. NOTE: Always cover vent hole in primer button when pushing. Additional priming may be necessary for first start if temperature is below 15°F. • Grasp starter handle and pull rope out slowly, until it pulls slightly harder. Let rope rewind slowly. • Pull starter handle rapidly. Do not allow handle to snap back. Allow it to rewind slowly while keeping a firm hold on the starter handle. • Repeat the previous steps until engine starts. To Stop Engine • Run engine for a few minutes before stopping to help dry off any moisture on the engine. • To help prevent possible freeze-up of starter, proceed as follows. Electric Starter: • Connect power cord to switch box on engine, then to 120 volt AC receptacle. With the engine running, push starter button and spin the starter for several seconds. The unusual sound made by spinning the starter will not harm engine or starter. Disconnect the power cord from receptacle first, and then from switch box. Recoil Starter • With engine running, pull starter rope with a rapid, continuous full arm stroke three or four times. Pulling the starter rope will produce a loud clattering sound, which is not harmful to the engine or starter. • Move throttle control to “stop” or “off” position. • Remove ignition key. Do not turn key. Disconnect the spark plug wire from the spark plug to prevent accidental starting while equipment is unattended. NOTE: Keep it in a safe place. Engine will not start without ignition key. Wipe all snow and moisture from the carburetor cover in the area of the control levers. Also, move control levers back and forth several times. To Engage Wheel Drive • With the engine running near top speed, move the shift lever into one of the six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist. NOTE: Use slower speeds in higher snow, and until you are familiar with the operation of the snow thrower. • Squeeze the traction control against the right handle and the snow thrower will move. Release it and the drive motion will stop. IMPORTANT: NEVER move the shift lever without first releasing the traction control. Doing so will cause premature wear to the drive system’s friction wheel. To Engage Augers To engage the augers and start the snow throwing action, proceed as follows: • Squeeze the auger control against the left handle. To disengage power to the augers: • Release both the auger control and the traction control, if engaged. The auger control can be locked so you can turn the electric chute directional control without interrupting the snow throwing process. Operating Tips NOTE: Allow the engine to warm up for a few minutes. The engine will not develop full power until it reaches operating temperature. 9 10 WARNING: The temperature of the muffler and the surrounding areas may exceed 150°F. Avoid these areas. • For the most efficient snow removal, remove snow immediately after it falls. • Discharge the snow downwind whenever possible. • Slightly overlap each previous path. • Set the skid shoes 1/4" below the shave plate for normal usage. The skid shoes may be adjusted upward (to lower the shave plate) for hard-packed snow. Adjust downward (to raise the shave plate) when using on gravel or crushed rock. SECTION 5: MAKING ADJUSTMENTS WARNING: NEVER attempt to make any adjustments while the engine is running, except where specified in the operator’s manual. Chute Assembly Adjustment The distance snow is thrown can be adjusted by adjusting the angle of the chute assembly. Refer to the Chute Tilt Control in the Know Your Snow Thrower Section. Traction Control Adjustment Refer to the information found under Final Adjustment in the Assembly Section to adjust the traction control. If you are uncertain that you have reached the correct adjustment, proceed as follows: WARNING: Drain the gasoline out of the snow thrower’s tank, or place a piece of plastic film under the gas cap to avoid spillage BEFORE making the adjustment. • Tip the snow thrower forward, allowing it to rest on the auger housing. • Remove the frame cover underneath the snow thrower by removing the six self-tapping screws. • With the traction control released, there must be clearance between the friction wheel...