Votes - 3, Average rating: 4
(
)
)
|
manual abstract
In-Lever sert universal joint pin (ensure ure 7 opening in pin is in line with NOTE: If the cables have become dis- small openings in universal connected, reinstall springs as shown in joint). Figure 8. 10. Place yoke end of crank rod around universal joint, lining up openings. Insert clevis pin through Auger Drive assembly and secure with cotter Traction Drive Spring (Short) pin. Spread ends of cotter pin to Spring (Long) lock in place. 11. Tighten aut on eye bolt. Make sure eye bolt is properly aligned and the crank can freely rotate. 12. Tighten all handle bolts. Cotter Pin // o,ev,sPin Universal Joi Crank Rod igure 8 Univer a Joint Pin Figure 6 TO INSTALL SHIFTER KNOB 1. Thread the 1/2-13 hex jam nut found in parts bag onto the threaded end of the shifter lever. See Figure 7. 2. Thread the shifter lever knob onto the threaded end of the shifter lever until it is snug against the hex jam nut and the lip is pointed away from the engine. Tighten the hex jam nut against the bottom of the shifter lever knob to lock in position. F-001088J 9 SNOW CHUTE ASSEMBLY 1. Turn crank assembly counterclockwise until it stop. 2. Position snow chute on inside of snow chute flange and align the three holes in the snow chute with holes on snow chute flange. (See Figure 9) 3. Place three 5/16-18 carriage bolts from inside of chute as shown in Figure 9. (hardware is found in parts bag). 4. Place three 5/16-18 flatwashers and three 5/16-18 nuts on outside of flange. 5. Tighten all four carriage bolts securely. NOTE: DO NOT overtighten carriage bolts. ,. HOW TO SET THE SKID HEIGHT Your snow thrower is equipped with height adjust skids on the outside of the auger housing. To adjust the skid HOW TO SET THE LENGTH OF THE The cables were adjusted at the factory and no adjustments should be necessary. However, after the handles are put in the operating position, the cables can v- CHECKLIST Before you operate your new snow thrower, to ensure that you receive the best performance and satisfaction from this quality product, please review the following checklist: _" All assembly instructions have been completed. _" The discharge chute rotates freely. _" No remaining loose parts in carton. 6. Turn crank assembly clockwise and make sure all carriage bolts are tight. Snow Chute \ Flatwasher Nut __Carriage "__Do N _tlR:move Flange Hardware Figure 9 height for different conditions, see To Adjust Skid Height paragraph in the Service And Adjustment section. CABLES be too tight or too loose. If an adjustment is necessary, see "How To Check And Adjust The Cables" in the Service And Adjustment section. While leaming how to use your snow thrower, pay extra attention to the following important items: _" Engine oil is at proper level. _" Make sure gas tank is filled properly with clean, fresh, unleaded gasoline. P" Become familiar with all controls- their location and function. Operate controls before starting engine. F-001088J 10 KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your SNOW THROWER to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. --Traction Drive Lever AugerElectric Drive Lever (left hand) Start (right hand) , Remote Button Primer Chute Control nition Bu Switch Lever Crank Assembly -'Chute Deflector Discharge Chute Choke Control Throttle Recoil Starter HeightAdjust Control Handle Skid Auger Drive Lever -Starts and stops the auger and impeller (snow gatheringand throwing) Traction Drive Lever -Propels the snow thrower forward and in reverse. Speed Shifter Lever -Selects the speed of the snow thrower (6 speeds forward and 2 speeds reverse). Crank Assembly -Changes the direction of snow throwing through the discharge chute. Chute Deflector -Changes the distance the snow is thrown. Discharge Chute -Changes the height and direction the snow is thrown. Height Adjust Skid -Adjuststhe ground clearance of the auger housing. ignition Key -Must be inserted to start the engine. Recoil Starter Handle -Starts the en gine manually. F-001088J Figure 10 Choke Control -Used to start a cold engine. Primer Button -Injects fuel directly into the carburetor manifold for fast starts in cold weather. Remote Chute Control Lever -Push forward to discharge snow high and far. Pull remote lever back to discharge snow down. Throttle Control -Controls the engine speed. Electric Start Button -(if so equipped) Used to start the engine using the 120 V electric starter. Shear Pin -Shear pins are designed to break (to protect the machine) if an obiect becomes lodged in the aguer housing. Toolbox -spare shear pins and spacers are located in toolbox. 11 The operation of any snow thrower can resultin foreign objects beingthrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating the snow thrower. We recommendstandardsafety glassesor a widevisionsafetymaskfor over y...