Votes - 1, Average rating: 3
(
)
)
|
manual abstract
YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE. PRODUCT SPECIFICATIONS Gasoline Capacity and Type: .5 Gal (1,89 Liters) Unleaded Regular only Oil Type(API SG–SL): SAE 30 (above 50°F) SAE 5W-30 or 10W-30 (32° to 50°F) SAE 5W-30 (below 32°F) Oil Capacity: 16 Ounces (0,47 Liters) Spark Plug: Gap: F6RTC 0.030" (0,762 mm) CUSTOMER RESPONSIBILITIES • Read and observe the safety rules. • Follow a regular schedule in maintaining, caring for and using your snow thrower. • Follow the instructions under “Maintenance” and “Storage” sec tions of this own er’s manual. TABLE OF CONTENTS SAFETY RULES ........................................................2-3 MAINTENANCE .....................................................13-14 PRODUCT SPECIFICATIONS ......................................3 SERVICE AND AD JUST MENTS ...........................15-17 CUSTOMER RESPONSIBILITIES ................................ 3 STORAGE ................................................................... 18 ASSEMBLY / PRE-OPERATION ............................... 4-6 TROU BLE SHOOT ING ................................................ 19 OPERATION ............................................................ 7-12 REPAIR PARTS ..................................................... 20-37 MAINTENANCE SCHEDULE ..................................... 13 WARRANTY ............................................ BACK COVER 3 PARTS PACKED SEPARATELY IN CARTON (1) POWER CORD (198563)(1) DISCHARGE CHUTE (3) RETAINER SPRINGS (169675) EXTRA SHEAR BOLTS AND NUTS (1) WASHER 3/8 (19131316) (1) LOCKNUT 3/8 (73800600) ROTATOR HEAD MOUNTING (1) AUGER CONTROL ROD SAFTEY IGNITION KEY(S) (422663) (1) MULTI- WRENCH (180684) (2) FLAT WASHERS (2) CARRIAGE BOLTS 3/8-16 x 2.25 (2) HANDLE KNOBS (2) SHEAR BOLTS 1/4-20 x 1-3/4 (2) LOCKNUTS (192090) 1/4-20 (73800400) ASSEMBLY / PRE-OPERATION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly, operation and maintenance of the product. Your new snow thrower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to com plete the as sem bly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hard ware you assemble must be tightened se cure ly. Use the correct tools as nec es sary to ensure proper tightness. REMOVE SNOW THROWER FROM CAR TON 1. Remove all accessible loose parts and parts boxes 2. Cut down all four corners of carton and lay panels flat. 3. Remove the two (2) screws securing the auger housing to the pallet. 4. Remove all packing materials ex cept plastic tie holding speed control rod to lower handle. 5. Remove the two (2) plastic ties securing the upper handle to the pallet. 6. Remove snow thrower from carton and check carton thor ough ly for ad di tion al loose parts. HOW TO SET UP YOUR SNOW THROWER TOOL BOX (See Fig. 8) A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox. from carton. 4 5 ASSEMBLY / PRE-OPERATION SPEED CONTROL ROD HANDLE KNOB LOWER HANDLE PLASTIC TIE UPPER HANDLE FIG. 1 INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod is installed on the snow thrower. 1. Remove plastic tie securing rod to lower handle. 2. With top end of rod positioned under left side of control panel, push rod down and insert top end of rod into hole in drive control bracket. Secure with retainer spring. TRACTION DRIVE CONTROL ROD VINYL SLEEVE FIG. 3 PLASTIC TIE NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making ad just ments to the skid plates. UNFOLD UPPER HANDLE 1. Raise upper handle to the operating position and tight en handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles. INSTALL SPEED CONTROL ROD (See Figs. 1 and 2) 1. Remove plastic tie securing rod to lower handle. 2. Insert rod into speed control bracket and secure with retainer spring. SPEED CON TROL ROD SPEED CONTROL BRACKET SPEED CONTROL LEVER FIG. 2 RETAINER SPRING TRACTION DRIVE CON TROL ROD DRIVE CONTROL BRACKET RETAINER SPRING TRACTION DRIVE CON TROL LEVER FIG. 4 ASSEMBLY / PRE-OPERATION INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) 1. Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray. Slide straight rod end through the small hole in the vinyl sleeve. Hook spring in hole in rod end. 2. Hook end of spring into control arm with loop opening up as shown. (See Fig. 5) 3. With top end of rod positioned u...