Votes - 3, Average rating: 3
(
)
)
|
manual abstract
The V-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower. WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing (1) from the frame assembly (2), it is important that an assistant stand in the op er - at ing position and hold the snow thrower handles (3). Serious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt chang ing process. 1. REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, outdoors, away from fi re or fl ame. Wipe up any spilled gasoline. 2. REMOVE DISCHARGE CHUTE - Loosen lock nut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower. 3. REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual. 4. REMOVE ENGINE PULLEY (A) - Remove bolt (B), lock washer (C) and fl at washer (D) securing pulley to engine crankshaft. Remove outside (auger) pulley (A) only from crankshaft. 5. SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two bolts (F) and lock washers (G) holding auger housing (1) and frame (2) together. WARNING: As the last bolt is removed, have your assistant careful ly lower the handles down to the ground. 6. REMOVE AUGER BELT (H) from around pulley (E). 7. RELIEVE TENSION ON TRACTION DRIVE BELT IDLER (J) and remove traction drive belt (K) from around pulleys. HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm (J) and rotate ratchet clockwise to relieve tension. 3 2 1 E D C B A F G J H K L M 2 1 Pour enlever le couvercle de la courroie 1. Enlevez les deux (2) vis (A) en fi xant le couvercle de la courroie (B) au chassis (C). 2. Enlevez le couvercle de la courroie. • Remplacez le couvercle de la courroie en installant le couvercle et serrez solidement. Desmontar el cubre correas 1. Desmontar los dos (2) tornillos (A) que sujetan el cubre correas (B) a la carcasa (C). 2. Desmontar el cubre correas. • Sustituir el cubre correas colocando la cubierta y los tornillos y apretando fi rmemente. Het verwijderen van de riemhuls 1. Verwijder de twee (2) schroeven (A) die de riemhuls (B) aan het frame (C) bevestigen. 2. Verwijder de riemhuls. • Zet de riemhuls weer terug door de huls en de schroeven terug te plaatsen en draai stevig aan. Rimuovere il coperchio della cinghia 1. Togliere le due (2) viti (A) che fi ssano il coperchio della cinghia (B) all’intelaiatura (C). 2. Togliere il coperchio della cinghia. • Rimettere coperchio e viti, stringendo bene. 48 1. ENTFERNEN SIE DAS BENZIN AUS DEM BENZINTANK – Lassen Sie das Benzin im Freien, fernab jeglichen Feuers oder jeglicher of...
Other models in this manual:Snow Blowers - PM55 (1.52 mb)
Snow Blowers - PM105 (1.52 mb)