Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
This cooker is not to be used as a space heater, especially if it is installed in marine craft or in a caravan. The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed. Ensure the kitchen is well ventilated. Keep natural ventilation holes open or install a mechanical ventilation device (mechanical extractor hood). Prolonged intensive use of the appliance may call for additional ventilation, for example opening of a window, or more effective ventilation, for example increasing the level of mechanical ventilation where present. I IInstalla nstallanstallation instruc tion instruction instructions tionstions Clearances Installation clearances and protection of combustible surfaces shall comply with the current local regulations eg. AG 601 (AS 5601) Gas Installations code. Installation shall comply with the dimension in Fig. 1 bearing in mind that: Overhead Clearances In no case shall the clearances between the highest part of the cooker be less than 600 mm or, for an overhead exhaust fan, 750 mm. AII other downward facing combustible surfaces less than 600 mm above the cooker surface shall be protected for the full width of the cooking surface in accordance with the standards noted above. In no case shall the clearance be less than 450 mm. Rear and Side Clearances Where the dimensions from the periphery of the nearest burner to any vertical combustible surface is less than 200 mm, the surface shall be protected in accordance with the standards to a height of not less than 150 mm above the cooking surface for the full width or depth of the cooking surface. Where the dimensions from the periphery of the nearest burner to any horizontal combustible surface is less than 200 mm, the horizontal surface shall be greater than 10 mm below the surface of the hob, or the horizontal surface requirement above. Protection of combustible surfaces The standards above specify that where required protection shall ensure that the surface temperature of the combustible surface does not exceed 65°C above room temperature. If you stand the cooker on a pedestal, make sure you provide safety measures to keep it in place. 500 mm 750 mm 105 mm 450 mm Cooker overall dimensions [mm] • height: min 900 - max 915 • width: 600 • depth: 600 Figure 1 Dimensions and distances from cooker Installation instructions Levelling the cooker To fit the adjustable feet: Place the cooker on its back as shown. Screw the four feet to the cooker. Stand the cooker and level it by screwing or unscrewing the feet with a spanner. Figure 2a Fitting the adjustable feet 0 + 8 mm + 8 mm + 15 mm Figure 2b Fitting the optional spacer (supplied in a separate kit) 8 Installation instructions Anti-tilt bracket Important! This appliance must be restrained to prevent accidental tipping by fitting a bracket to the rear of the appliance and securely fixing it to the wall. To fix the anti-tilt bracket: After you have located where the cooker is to be positioned mark, on the wall, the place where the two screws of the anti-tilt bracket have to be fitted. Please follow the indications given in the drawing below. Make two 8 mm diameter holes on the wall and insert the plastic plugs. Loosely attach the anti-tilt bracket with two screws. Move the cooker to the wall and adjust the height of the anti-tilt bracket so that it can engage in one slot of the cooker back. Tightly attach the anti-tilt bracket. Push the cooker against the wall so that the anti-tilt bracket is fully inserted in one slot of the cooker back. 365 235 600 mm min 105max 120 0 + 15 Figure 3 Fitting the anti-tilt bracket Installation instructions Gas supply The gas connection must be carried out by an authorised person according to the relevant standards. Before connecting the appliance to the gas main, mount the brass conical adaptor onto the gas inlet pipe, upon which the gasket has been placed (see figures following). Conical adaptor and gasket are supplied with the appliance (packed with conversion kit for use with Natural gas or LPG gas). This appliance is suitable for use with Natural Gas or LPG gas. (Check the “gas type” sticker attached to the appliance). For Natural Gas models the gas supply is connected to the pressure regulator which is supplied with the appliance. Adjust the regulator to obtain a test point pressure of 1 kPa with the two semi-rapid burners operating at the maximum. For LPG gas models the gas supply is connected to the test point adaptor which is supplied with the appliance and ensure that the supply pressure is regulated to 2.75 kPa. The connection must be made at the rear of appliance (left or right); the pipe is not to cross the cooker. Close off the unused inlet with the cap and sealing gasket supplied (Fig 7). IMPORTANT: Use two spanners to tighten or loosen the connecting pipe as shown following. Gas connection for LPG GAS Gas connection for NATURAL GAS Gas inlet pipe Nipple Gasket Brass conical adaptor (Thread tight: u...