Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety. Basee sur la legislation des Etates membres relative a la compatibilite electromagnetique et a la securite des produits. Uber die Annaherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Vertraglichkeit und Produktsicherheit entsprechen. Basado en la aproximacion de las leyes de los Paises Miembros respecto a la compatibilidad electromagnetica y las Medidas de seguridad relativas al producto. Questa dichiarazione e basata sulla conformita dei prodotti alle norme seguenti: This declaration is based upon compliance of the products to the following standards: Cette declaration repose sur la conformite des produits aux normes suivantes: Diese Erklarung basiert darauf, da. das Produkt den folgenden Normen entspricht: Esta declaracion se basa en el cumplimiento de los productos con las siguientes normas: EN 55022, August 1994: LIMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE CHARACTERISTICS OF INFORMATION TECHNOLOGY EQUIPMENT (ITE) EN 50082-2, March 1995: ELECTROMAGNETIC COMPATIBILITY. GENERIC IMMUNITY STANDARD. PART 2: INDUSTRIAL ENVIRONMENT Lippo di Calderara, 07/03/2001 Quality Assurance Supervisor Product names mentioned herein are for identification purposes only and may be trademarks and or registered trademarks of their respective companies. Datalogic S.p.A. reserves the right to make modifications and improvements without prior notification. . - 2001 Datalogic S.p.A. Ruggero Cacioppo 821000560 CONTENTS GUIDE TO INSTALLATION.............................................................. iv SAFETY PRECAUTIONS .................................................................vii Power Supply ....................................................................................vii 1 GENERAL FEATURES......................................................................1 1.1 Description .........................................................................................1 2 INSTALLATION .................................................................................2 2.1 Package Contents..............................................................................2 2.2 Opening the Device............................................................................3 2.3 Mechanical Installation.......................................................................4 2.4 Electrical Connections and Setup ......................................................6 2.4.1 Power Supply .....................................................................................7 2.4.2 System Wiring....................................................................................8 2.4.3 Chassis Grounding Jumper Settings................................................10 2.4.4 Multidrop Address Selection.............................................................11 2.4.5 RS485 Bus Termination...................................................................12 2.4.6 Connection to a Multiplexer..............................................................13 2.4.7 OM4000 Jumper Settings.................................................................14 2.5 9-Pin Scanner Auxiliary Serial Interface...........................................15 2.6 Scanner Requirements.....................................................................16 2.7 Operating Modes..............................................................................16 2.7.1 GET/SEND Buttons..........................................................................17 2.7.2 LED Indicators..................................................................................18 3 TECHNICAL FEATURES ................................................................19 GUIDE TO INSTALLATION The following can be used as a checklist to verify all of the steps necessary for complete installation of the C-BOX 200. 1) Read all information in the section "Safety Precautions" at the beginning of this manual. 2) Correctly position and mount the C-BOX 200 within the reach of the barcode scanner cable, according to the information in paragraph 2.3. 3) Provide correct system cabling according to the signals necessary for your application and RS485 settings (see all sub-paragraphs under 2.4) The installation is now complete. C-BOX 200 General View 1 2 3 1 2 3 Figure A 25-pin scanner connector Compression connectors Cover screws (4) C-BOX 200 General View 4 10 1 2 6 7 8 9 12 5 3 11 1 2 3 5 4 6 Figure B Power switch (ON/OFF) 7 8 9 10 GET button Spring clamp terminal blocks SEND button Multidrop address switches Auxiliary port connector Chassis grounding selector Power on LED 11 Termination resistance switch Warning LED 12 OM4000 jumpers Tx LED SAFETY PRECAUTIONS POWER SUPPLY ATTENTION: READ THIS INFORMATION BEFORE INSTALLING THE PRODUCT -This product is intended to be installed by Qualified Personnel only. The C-BOX 200 is intended to be supplied by an NEC Class ...