Votes - 2, Average rating: 4
(
)
)
|
manual abstract
An antivibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool. SPECIAL NOTICE: For users on U.S. Forest Land and in some states, including California (Public Resources Codes 4442 and 4443), Idaho, Maine, Minnesota, New Jersey, Oregon, and Washington: Certain internal combustion engines operated on forest, brush, and/or grass covered land in the above areas are required to be equipped with a spark arresting screen, maintained in effective working order, or the engine must be constructed, equipped, and maintained for the prevention of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure to follow these requirements is a violation of the law. This unit is not factory equipped with a spark arresting screen; however, a spark arresting screen is available as an optional part. If a spark arresting screen is required in your area, contact your authorized service dealer for the correct kit. The spark arresting screen, blower tubes, and nozzles must be assembled to unit to be in full compliance with regulations. ASSEMBLY WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or accessing movable parts. WARNING: If you receive your unit assembled, check each step to insure your unit is properly assembled and all fasteners are secure. Follow all safety information in the manual and on the unit. D A standard screwdriver is required for assembly. BLOWER TUBE ASSEMBLY 1. Align the rib on the blower tube with the groove in the blower outlet; slide the tube into place. --3 NOTE: Tube clamp must be loose enough to allow blower tube to be inserted in blower out let.Loosentubeclampbyturningknobcounterclockwise. BlowerTubeBlowerOutletRibGroove2.Tightenthetubeclampbyturningtheknobclockwise. 3. To remove the tube, turn the knob counterclockwise to loosen clamp; remove tube. VACUUM BAG ASSEMBLY 1. Open the zipper on the vacuum bag and insert the elbow tube. 2. Push the small end of the elbow tube through the small opening in the bag. - -- -- 4 -- Small Opening Zipper Opening Elbow Tube Rib NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube, and the rib on the elbow tube is on the bottom. 3. Close the zipper on the bag. Make sure the zipper is closed completely. 4. Remove blower tube from engine. Rib Groove 5. Insert the elbow tube into the blower outlet. Make sure elbow tube rib is aligned with the blower outlet groove. 6. Turn clamp knob clockwise to tighten. VACUUM TUBE ASSEMBLY WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. 1. Align the lower vacuum tube as shown. Push lower vacuum tube into upper vacuum tube. Lower Vacuum Tube Upper Vacuum Tube 2. Insert a screwdriver into the latch area on the vacuum inlet cover. Latch Area Blower Outlet Vacuum Inlet Cover Latch Area 3. Gently tilt the handle of the screwdriver toward the back of the unit while pulling up on the vacuum inlet cover with your other hand. 4. Hold the vacuum inlet cover open until upper vacuum tube is installed. Vacuum Inlet Vacuum Inlet Cover Retaining Post 5. Place the hooks on the vacuum tube on the retaining posts; pivot tube into position. Secure vacuum tube by turning the knob clockwise until tight. Hooks Knob 6. When converting back to the blower feature, make sure latch on the vacuum inlet cover is securely fastened. SHOULDER STRAP ADJUSTMENT 1. Hold the unit as shown. 2. Pass the shoulder strap over your head and onto your right shoulder. 3. Extend your left arm toward the rear of the vacuum bag. 4. Adjust shoulder strap until the vacuum bag/shoulder strap seam lies between your thumb and index finger. 5. Make sure air flows freely from the elbow tube into bag. If bag is kinked, the unit will not operate properly. -- 5 -- OPERATION KNOW YOUR BLOWER READTHIS INSTRUCTIONMANUAL ANDSAFETY RULES BEFORE OPERATINGYOURUNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. Choke Lever Fuel Mix Fill Cap Starter Rope Throttle Lever Spark Plug Blower Tube Primer Button Rear Handle Lower Vacuum Tube Upper Vacuum Tube Vacuum Bag Elbow Tube THROTTLE LEVER The THROTTLE LEVER is used to select the desired engine speed and to stop the engine. Move the throttle lever to the position for full speed operation. Move the throttle lever to the position for idle speed. To stop the engine, move the throttle lever to the STOP positi...