Votes - 3, Average rating: 4.3 ( )

Manafacture: Stihl File size: 1.99 mb File name: Language of manual:

Do not fill fuel canisters that are sitting in or on a vehicle. The canister should be kept tightly closed in order to avoid any moisture getting into the mixture. The machine‘s fuel tank and the canister in which fuel mix is stored should be cleaned as necessary. Fuel mix ages Only mix sufficient fuel for a few days work, not to exceed 3 months of storage. Store in approved fuel-canisters only. When mixing, pour oil into the canister first, and then add gasoline. Close the canister and shake it vigorously by hand to ensure proper mixing of the oil with the fuel. Gaso-Oil (STIHL 50:1 or equivaline lent high-quality oils) US gal. US fl.oz 1 2.6 2 1/2 6.4 5 12.8 Dispose of empty mixing-oil canisters only at authorized disposal locations. BG 56, BG 56 C, BG 66, BG 86, BG 86 C, SH 56, SH 56 C, SH 86, SH 86 C English Fueling Starting / Stopping the Warning! Engine After fueling, tighten fuel cap as securely as possible by hand. Starting the engine Change the fuel pick up body every N Observe safety precautions. year 295BA064 KN295BA065 KNBefore fueling, clean the filler cap and 1295BA066 KN N Press the fuel pump bulb (1) at least five times – even if the bulb is filled with fuel. Adjusting the setting lever Only on BG 86, SH 86 295BA069 KN the area around it to ensure that no dirt falls into the tank. Before storing your machine for a long period, drain and clean the fuel tank and Always thoroughly shake the mixture in run engine until carburetor is dry. the canister before fueling your machine. Warning! In order to reduce the risk of burns or other personal injury from escaping gas vapor and fumes, remove the fuel filler cap carefully so as to allow any pressure build-up in the tank to release slowly. N To start, move the setting lever to the run position F The setting lever selects and holds any throttle position between idle and full throttle. BG 56, BG 56 C, BG 66, BG 86, BG 86 C, SH 56, SH 56 C, SH 86, SH 86 C English Adjusting the choke knob Starting N Do not let the starter grip snap back. Guide it slowly back into the housing If the engine is cold so that the starter rope can rewind properly. Other hints on starting 296BA006 KN NPlace the unit on the ground: NMake sure you have a firm footing: Hold the unit firmly with your right hand on the housing and press If the engine stops while the choke knob in on g or during acceleration N Move the choke knob to < and continue cranking until the engine runs. N Choke-Drehknopf auf g If the engine is warm If the engine does not start N Make sure all settings are correct (choke knob, setting lever in run position F). N Repeat the starting procedure. If fuel tank has been run completely dry and then refueled 1295BA066 KN N Choke-Drehknopf auf < down. Also use this setting if the engine has been running but is still cold. N Hold the starter grip with your left hand. Models with ErgoStart N Pull the starter grip steadily. Models without ErgoStart N Pull the starter grip slowly until you feel it engage and then give it a brisk strong pull. Do not pull out the starter rope all the way – it might otherwise break. N Press the fuel pump bulb (1) at least five times – even if the bulb is filled with fuel. N Now start the engine. 295BA067 KN 295BA068 KN BG 56, BG 56 C, BG 66, BG 86, BG 86 C, SH 56, SH 56 C, SH 86, SH 86 C English As soon as the engine runs BG 86, SH 86 Cleaning the Air Filter If there is a noticeable loss of engine power 295BA073 KN NMove the setting lever to 0 – the engine stops – the setting lever 295BA071 KN3 1295BA074 KN 2 N Blip the throttle trigger (3) – the choke knob moves to the run springs back to the on position. position F – the engine returns to idle speed. Stopping the Engine. N Turn the filter cover lock (1) counterclockwise to the vertical position. BG 56, BG 66, SH 56 N Remove the filter cover (2). N Clean away loose dirt from around the filter. 295BA072 KN NMove the stop switch to 0 – the engine stops – the stop switch springs back to the on position. 3295BA075 KN 25 N Pull off the retainer (3) and take the filter (4) out of the filter housing (5). N Install a new filter. As a temporary measure you can knock it out on the palm of your hand or blow it out with compressed air – do not wash. Replace damaged parts. BG 56, BG 56 C, BG 66, BG 86, BG 86 C, SH 56, SH 56 C, SH 86, SH 86 C English Installing the filter N Fit the filter in the filter housing and push the retainer into position. N Refit the filter cover and turn the filter cover lock to the horizontal position, Engine Management Exhaust emissions are controlled by the design of the fundamental engine parameters and components (e.g. carburation, ignition, timing and valve or port timing) without the addition of any major hardware. Adjusting the Carburetor The carburetor comes from the factory with a standard setting. This setting provides an optimum fuel-air mixture under most operating conditions. With this carburetor it is only possible to adjust the high speed screw within fine limit...

Download now

Please, enter two numbers from picture: