Votes - 3, Average rating: 5 ( )

Manafacture: Craftsman File size: 1.04 mb File name: Language of manual:

Press the tubes together until the lower tube is fully seated in the upper tube. You will know the tubes are fully seated when the lower tube will no longer go into the upper tube. (About 3 inches). \ Attach Upper & Lower Tubes Figure 8 Figure 5 H,n = n,,,,, ====r= ASSEMBLY =n = =,,=, ATTAC'HING COLLECTION BAG (Fig. 9 ) • Slide the opening of the collection bag over the blower outlet. Pull the strap with Velcro tightly through the buckle and secure the Velcro tabs. NOTE: Make sure the strap with Velcro is located on the housin,q as shown. Strap Collection Bag .._ Blower Outlet Figure 9 ADJUSTING THE SHOULDER STRAP ON THE COLLECTION BAG (Fig. 10 & 11 ) • Carefully loop the shoulder strap through the buckle as shown in the illustration. Notice the first in and last in is the same opening. • With your left hand hold the unit in an upright position. Support the lower vacuum tube on the ground. Make sure the blower outlet and collection bag are positioned on your right-hand side. • Place the shoulder strap over your left shoulder. • Adjust the shoulder strap to allow a free flow of air from the blower outlet. If the collection bag is kinked, the unit will not operate propedy. NOTE: The shoulder strap is designed to position the collection bag on your shoulder without kinks. The strap is not intended to support the weight of the unit. Last In First IJ_ Figure 10 Shoulder strap on left shoulder Free flow of air. No kinks In collection bag Figure 11 -8 BLOWER CONVERSION • Stop unit and disconnect from power source. • Remove the vacuum tubes and collection bag. • Install the inlet restrictor. NOTE: The inlet restfictor is for blower enhancement onty. The unit may still be used if the inlet restrictor is iost or misplaced. • Secure the inlet cover making sure that the latch is securely fastened. o Reinstaf! the blower tubes. Refer to "Blower Tube Assembly" section. EXTENSION CORD ATTACHMENT (Fig. 12&13) • Use only an A.C. voltage supply as shown on the nameplate of the unit. • The extension cord used to reach power source must be: - Polarized and specifically marked as suitable for outdoor use. The cord must be marked with the suffix 'IiV-A" ("W" in Canada). -Heavy enough to carry the current from the power source the full length of the extension cord to the unit. Otherwise, loss of power and overheating can occur causing damage to the unit, Refer to the "Minimum Wire Gauge Recommendation Chart" for minimum wire gauge recommendations. The cord must be marked with the proper wire gauge. (Appropriate extension cords are available.) -In good condition. Cord insulation must be intact with no cracks or deterioration; plug connectors must be undamaged. Replace damaged cord. • Secure extension cord to the unit as shown. • Plug extension cord into the unit. To reduce the risk of electric shock, this unit has a polarized plug (one blade is wider than the other). This plug will fit into a polarized extension cord only one way. Ifthe plug does not fit fully into the extension cord, reverse the cord. If it still does not fit, make sure you have a polarized extension cord. If the extension cord does not fit into the outlet, reverse the cord. If it still does not fit into the outlet, contact a qualified electrician to installthe proper outlet. Do not change the !ugor socket of the unit or extension cord in any way. MINIMUM WIRE GAUGE RECOMMENDATION CHART VOLTS 25 FT. 50 FT. 100 FT. 150 FT. 12018 16 1412 A.W.G.* A.W.G.* A.W.G.* A.W.G.* Figure12 *American Wire Gauge Cord from Unit,,_ Extension Cord Cord Socket Figure 13 =n== = ASSEMBLY ii i CHECK LIST = Check all fasteners. Make sure they are tight and there are no loose parts. • Make sure the blower tube is firmly seated in the blower outlet• • If you are using the unit as a blower, make sure the inlet cover is latched_ = In blower mode. check to insure the nozzle is securely seated inthe blower tube. • If you are using your unit as a vacuum, make sure the vacuum tubes are firmly connected, and positioned as shown inthe assembly illustrations. • Make sure the collection bag is correctly adjusted with the shoulder strap on your right shoulder, • Make sure your extension cord is marked with a suffix of "W-A". ("W" in Canada). -9 KNOW YOUR ELECTRIC BLOWER READ THIS OPERATOR'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR ELECTRIC BLOWER. Compare the ilfustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. TOP HANDLE AIR VENTS | ON/OFF SWITCH \ INLET COVER LATCH REAR HANDLE The ON/OFF SWITCH is used to tum on the unit. The INLET COVER LATCH is used to open the inlet cover for attaching Upper Vacuum Tube. The TOP HANDLE is used to hold the unit during the Blower and Vacuum mode. DOUBLE INSULATION CONSTRUCTION ALL ELECTRICAL REPAIRS TO THIS _ WARNING HOUSING, UNIT, INCLUDING SWITCH, MOTOR, ETC., MUST BE DIAGNOSED AND REPAIRED BY QUALIFIED SERVICE PERSONNEL. REPLACEMENT PARTS FOR A DOUBLE INSULAT...

Download now

Please, enter two numbers from picture: