Votes - 1, Average rating: 4
(
)
)
|
manual abstract
Description Quantity Blower with speed control and 6-foot cord. 1 Instruction Sheet 1 103650-01 Control Knob 1 103651-01 Lock Nut 1 M11084-38 #8 x 3/8" sheet metal screws 5 101629-01 Plastic Hole Bushings 2 101584-05 Wiring Diagram Decal 1 Tools Required • Pliers • Phillips Screwdriver If any of these pieces are missing or damaged, or if the installation instructions for your fireplace or stove are not included in this manual, contact the dealer where you purchased this kit or DESA at 1-866-672-6040 for referral information. Save this manual for future reference.Save this manual for future reference. 108319-01B 2 Forr morre iinfforrmattiion,, viisiitt Note: Appearance of firebox may vary slightly depending on model. 1. Remove the firebox bottom: a. Remove the 4 screws that secure the bottom of the firebox (see Figure 1). b. Carefully raise and remove the firebox bottom from the firebox. INSTALLING BLOWER ACCESSORY IN A 32" FIREBOX NOTICE: If a log set is currently installed in the firebox, disconnect log set from gas supply and remove from firebox. Contact a qualified service person to do this. WARNING: If there is a duplex electrical outlet installed in the right side of the bottom of the fireplace base area, be sure that the electrical power to the outlet is turned off before proceeding with blower installation. Failure to do this may result in serious injury. CAUTION: Never touch the blower wheel while in 2. Attach the power cord to the blower motor by firmly pushing the two operation. female terminals at the end of the power cord onto the two spade terminals on the blower motor. 3. Attach green ground wire from power cord to blower housing using screw provided (see Figure 2). Tighten screws securely. 4. Place the blower against lower rear wall of firebox wrapper with the exhaust port directed upward. Align the holes in top mounting tabs of blower with holes in wall of wrapper (see Figure 2). Using 2 screws provided, mount blower and tighten screws securely. 5. Be certain that all wire terminals are securely attached to terminals on blower motor and that the screw retaining the green ground wire is tight. 6. Locate the plastic hole plug installed in the 3/8" diameter opening in the lower right side of the firebox front panel (see Figure 2). Remove the plastic plug and discard. 7. Place speed control against inner wall of front panel, pushing the plastic control shaft forward through the opening (see Figure 3). Figure 1 - Removing Screws from Firebox Bottom 8. While supporting speed control, secure control shaft with lock nut by pushing and turning lock nut with pliers clockwise until it is tight against front panel. Place control knob provided on shaft (see Figure 3). 9. Plug in blower power cord. a. If your firebox is installed as a freestanding unit, determine whether the power cord will exit the left side or the right side of the firebox. Install 1 plastic bushing provided into the 1 1/2" hole in the floor support on the exit side. Install the second plastic bushing provided into the 1 1/2" hole in the outer casing through which the power cord will exit (see Figure 4). Route power cord through both plastic bushings and plug the power cord into a 3-prong grounded wall receptacle near the firebox. b. If your firebox installation is recessed and/or pre-wired, plug the power cord into the duplex outlet provided. Refer to your firebox owner’s manual for instructions on wiring the duplex outlet. Screws Figure 2 - Mounting Blower to Firebox Screws Blower Lower Rear Wall of Firebox Wrapper Floor Supports Top Mounting Tab Exhaust Port Plastic Hole Plug Screw Note: Appearance of fireplace may vary by model. Figure 4 - Installing Plastic Bushing for Power Cord Plastic Bushing Speed Control Lock Nut Control Knob Control Shaft Figure 3 - Attaching Speed Control INSTALLING BLOWER ACCESSORY IN A 32" FIREBOX 108319-01B 33 Forr morre iinfforrmattiion,, viisiitt 10. Turn on power to duplex outlet if previously turned off per the warning in step 1, page 2. 11. Check to make sure that the power cord is completely clear of the blower wheel and that there are no other foreign objects in blower wheel. Turn blower on and check for operation. 12. Peel off the backing paper and stick the supplied wiring diagram decal on the firebox bottom approximately 12" in front of the blower. 13. Replace bottom of firebox. Note: Make sure the back of the firebox bottom slides under the rear of the firebrick (lift the firebrick up if necessary.) 14. Reattach firebox bottom using 4 screws removed in step 1, page 2. Note: Discard the remaining hardware items. 15. Install the log set heater according to the installation instructions supplied with the heater. OPERATING THE BLOWER Light your gas appliance with the blower off. After about 15 minutes, turn the blower on to deliver heated air at the top louvers. The blower features a variable control which allows you to select the speed you desire. Note: Peri...