Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
Delay LCR VarEFKEYELEMPART OCTAVE PAGE 13 . Settings: Details are given in the Effect Type list in the separate Data List. 14. Variation Parameters Set the various Variation effect parameters. . Settings: The number of parameters and the contents of each screen will vary depending on the selected Effect Type. Details are given in the Effect Type/ Parameter list in the separate Data List. Multi Common Effect 57 15.15. This determines how the Variation Effect is used in the Set the send level of the signal sent from the Variation signal processing chain — as an Insertion effect or as a Effect to the Reverb Effect. System effect. Multi Mode VarConnect INSKEYELEMPART OCTAVE PAGE 15 SndVar Rev 000KEYELEMPART OCTAVE PAGE 18 . Settings: INS (Insertion), SYS (System) n The function of the Variation Effect changes depending on this setting, as do the types of parameter changes. nFor more details on System and Insertion Effects, see page 53. 16. Var Return (Variation Return) Set the Return level of the Variation Effect. Var Return 064KEYELEMPART OCTAVE PAGE 16 . Settings: 0 ~ 127 n This can be set only when Variation Connection (above) is set to “SYS.” When Variation Connection is set to “INS,” “***” appears in the display and the setting cannot be changed. 17. Var Pan (Variation Pan) Set the stereo pan position of the Variation Effect. Var Pan CKEYELEMPART OCTAVE PAGE 17 . Settings: L63 (Left) ~ C (Center) ~ R63 (Right) n You can also enter the settings below using the numeric keypad. 1~63: L63~L01 64: C (Center) 65~127: R01~R63 n This can be set only when Variation Connection (above) is set to “SYS.” When Variation Connection is set to “INS,” “***” appears in the display and the setting cannot be changed. . Settings: 0~127 nThis can be set only when Variation Connection (above) is set to “SYS.” When Variation Connection is set to “INS,” “***” appears in the display and the setting cannot be changed. 19. SndVarCho (Send Variation to Chorus) Set the send level of the signal sent from the Variation Effect to the Chorus Effect. SndVar Cho 000KEYELEMPART OCTAVE PAGE 19 . Settings: 0~127 nThis can be set only when Variation Connection (above) is set to “SYS.” When Variation Connection is set to “INS,” “***” appears in the display and the setting cannot be changed. 20. MW VarCtl (MW Variation Effect Control Depth) This determines the degree to which the Modulation wheel controls the Variation Effect. MW VarCtl +00KEYELEMPART OCTAVE PAGE 20 . Settings: –64~+63 nThis can be set only when Variation Connection (above) is set to “INS.” When Variation Connection is set to “SYS,” “***” appears in the display and the setting cannot be changed. nThe particular parameter that can be controlled with the Modulation wheel is fixed for each of the Variation effects. Refer to the separate Data List for details. 58 Common Effect 21.21.l (AC1 Variation Effect Control Depth) This determines the degree to which the Assignable Controller 1 controls the Variation Effect. AC1VarCtl +00KEYELEMPART OCTAVE PAGE 21 . Settings: –64~+63 n This can be set only when Variation Connection (above) is set to “INS.” When Variation Connection is set to “SYS,” “***” appears in the display and the setting cannot be changed. n The particular parameter that can be controlled with the Assignable Controller 1 is fixed for each of the Variation effects. Refer to the separate Data List for details. n For information on the AC1, refer to AC1 CC No (pages 66 and 92 ) in the Multi and Utility modes. Part (Settings for each Part) The following is an explanation of the Part parameters used to edit each Multi. nRefer to the Function Tree chart (page 20) or the Parameter Table (page 22). Voice Selection (PAGE 1) Part Mix (PAGES 2 to 5) Part General (PAGES 6 to 9) Part Tone (PAGES 10 to 14) Part Controller (PAGES 15 to 21) Part Effect (PAGES 22 to 24) 1. Voice Selection You can assign a Voice to each Part. Use the [+] and [–] buttons to select the Part, then select its Voice. The display will vary as follows according to the Memory selected. nSpecify the particular Voice Memory by pressing the appropriate Memory button: PRESET, USER or GM/XG. nTo select a Drum Voice, simultaneously hold down the [DRUM] button and press the appropriate Memory button: [USER] or [GM/XG]. nThe Voice can be set by using the same method as with Category Search (page 35). nFor details about Categories, refer to the Category List on page 71. For details about using Category Search, see page 35. PRESET StPiano1 PR001KEYELEMPART OCTAVE PAGE 1 . Settings: PR001 ~ PR128 Multi Common Effect/Voice Selection 59 R 3. Pan . Settings: US001~US128, USDR01~USDR02 Set the stereo pan position of the Part. Synth St US001KEYELEMPART OCTAVE PAGE 1Pan CKEYELEMPART OCTAVE PAGE 3 1 Multi Mode GM/XG GrandPno XG001KEYELEMPART OCTAVE PAGE 1 Use the [E] and [F] buttons to switch among the different banks for selecting program numbers. . Settings: Bank Select: BK*** (Refer to the XG Voice List and XG Drum List in the sepa...