Votes - 3, Average rating: 5
(
)
)
|
manual abstract
priate level ■ If IhB MIDI LOCAL CONTROL is set to off, sel il to on (refer lo page 9) MIDI E> UNE DUT D ÍMDNQ © S пГ PHONES L Connections 10 □ QTG0653 Assembly Follow Ihe steps below la assemble your Technics piano Make sure you are using Ihe correct parts and lhal they are in Ihe correct direction ■ Al leasl 2 people arB required Far assembly - Ta disassemble Ihe piano, reverse Ihe procedure 1 Remove Ihe packing and take Ihe parts out of Ihe car-lon Confirm thal all Ihe parts nn the printed list are present 5 Secure the piano body !□ the stand ...........® Brass-colored screw 4 " 'P Black screw B 4^ Clamp 3 2 Affix Ihe right and iBft side planks to the pedal box Lis I (1) Use the 4 brass-colored screws la secure Ihe planks (2) Loosen Ihe pedal card, slowed an the inner sidE af Ihe pedal box, and eilend il 3 Affix Ihe crass bar Black screw Turn each of Ihe 4 black screws 5 or 6 limes (do nol screw in lightly al Ihis lima) 4 Place the pianc body on IhB sland WARNING Avoid pinching your fingers NejIb 1 Holding the piano body at least 10 cm in from the edge, place il an the sland sD that il does nal lall off NdIb 2 If the piano body is placed lao far la IhB nghl nr left, or ta Ihe Irani or back, il will become unstable (1) Insert 2 black screws in Ihe 2 rear screw holes an Ihe underside cT (he piana body, and lurn each screw 5 ar 6 limes Push the piana body forward sa thal the screws are fully inserted in Ihe cutout of Ihe melal prnce an either side plank (This enables you In easily position Ihe piano body on the stand ) (2) Adjust Ihe piano bady sa lhal it evsnly aligns with Ihe stand (3) Positioning the piano body an the sland, confirm lhal the 4 black screws can easily be inserted (4) Tighlen Ihe 4 screws securely (5) Securely tighten the 4 black screws lhal affix Ihe cross bar 6 Conned the pedal cord and power card la the terminals (1) Plug Ihe pedal card and power card inlo Ihe terminals on IhB fBar of Ihe piano (2) Remove the backing Tram Ihe clamps and affix Ihem as shown in Ihe ligure Secure Ihe pedal card to Ihe clamps 11 QQTGÜB53 ■ Confirm' After assembling, check these points ■ Are any parts left over7 —* Check the assembly procedure again ■ Does the piano rattle when it is rocked7 —* Make sure all Ihe screws are securely lightened ■ Is IhB power cord firmly inserted7 —* Check again ■ Is the plug ol the pedal cord inserted as far in In the connector terminal as it will go7 —» If it is nol completely inserted, the sustain and ulher pedal functions may not work ■ When Ihe piano has been moved Dr transported, retighlen the screws securely ■ After setting up After assembling the instrument and positioning it in its intended place of use, remove the 3 gold screws and 3 spacers lhal secure Ihe sliding keyboard Nate Please keep Ihe securing screws and spacers in a safe place for use in (he event of a future move ■ Caution when transporting this instrument When transporting Ihis inslrumenl (during a move, inr example), affm the special securing parts la Ihe keyboard section At this time, da not completely stow the keyboard section inside Ihe main unit, bul allow it Id protrude about 2 cm towards the front, affixing it by following the procedure belaw (1) PlaCB Bach nf thB three spacars so thal Ihsy will be positioned in the gap between Ihb screw and the panel (2) Partly scrBW in Ihe 3 securing screws, making sure thal each of the spacers is lightly held in place (3) Securely tighten each screw ■ Caution Please do not sit on or hang from the keyboard section (If a strang farce is applied, there is a danger of its falling ) iring screws, Id Ihe sland 12 QQTG0E53 MIDI Implementation Chart Digital piano [ 5X-NP1D ] Function Transmitted Recognized Remarks Basic Default — 1 Channel Changed 1-16 1-1 G □ sfault 3 3 Mode Messages ж X Altered — — Note Z1-10B □-127 Number True voice — 0-127' Velocity Note ON Ü 0 Note OFF M(9nh V=0) X After Key's X X Touch Ch’s X X Pilch Bend M X о 0 sustain pedal Control 64 о о soslenulo pedal Change Б7 о О soft pedal 74 X О brilliance Prog о О 0 built-in sounds arranged Change TrUE # — 1-120 in GM map System Exclusive о О System Sang Pas X X SDng Sel м м Cum mem Tune X X System Clock X X Real Time Commands X / start/slop, continue Aun Local GN/OFF X О All Nales OFF X О Messages Active Sense О О Resel X X Notes ‘Depends on Ihe TRANSPOSE selling Made 1 OMNI ON, POLY Made 2 OMNI ON, MONO O Yes Made 3 □MNI OFF, POLY Made 4 OMNI OFF, MONO X No 13 QQTG0E53 Specifications SX-NP10 KEYBOARD SB KEYS (WITH TOUCH RESPONSE) SOUND GENERATOR PCM MAX POLYPHONY 32 NOTES SOUND B SOUNDS GRAND PIANO, UPRIGHT PIANO, E PIANO 1, E PIANO 2, HARPSI, VIBES, STRINGS, PIPE ORGAN PEDALS SUSTAIN, SOFT, SOSTENUTO FUNCTIONS MAIN VOLUME, MIC VOLUME, DEMO, TUNING, REVERB, BASIC CHANNEL, LOCAL CONTROL TERMINALS PHONES » 2, MIDI (IN, OUT), AUX IN (R, L), LINE OUT (R/MONO, L), MIC, USB OUTPUT 00 W (4D W ï 2) SPEAKERS 14 cm x 2 POWER REQUIREMENT 05 W/110 W (NORTH AMERICA AND MEXICO) AC 120/220/240 V 50/G0 Hz AC 120V 60 Hz (NORTH AMERICA AND MEXICO) AC 230-240V 50/60 Hz (EUROPE, AUSTRALIA, NEW ZEALAND, SINGAPORE AND PHILIPPINES) DIMENSIONS (WxH*D)' 142 3 cm m 0B 7 cm x 55 9 cm (56-1/32" m 3B-27/32' m 22") D 45 1 cm (17-3/4") when the keyboard seclron is closed NET WEIGHT 5B kg (127 9 lbs ) ACCESSORIES MUSIC STAND, AC CORD, CD ROM * Including Ihe music sland - Design and spEcificalions are subjacl la change without nclice DEMÜ Songs No TITLE COMPOSER 1 Amazing Gracs traditional 2 Arabeske Op 1 H Schumann 3 Beauiiful Dreamer Fnsler 4 Panasonic Original 5 Swannee Rivbt traditional 6 Danny Boy traditional 14 QQTG0653 ■ Supplied accessory Please check the supplied accessory -s? □ AC cord EH Music Stand B □ CD-ROM NOTE The included AC cord is lor use wilh this unil only Da n□ L use it wilh Dlher equipment 15 QQTG0653 PANASONIC CONSUMER ELECTRONICS COMPANY DIVISION OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Primed ln Jupon One Panasonic Way SHcaucus Naw Jersey Q7G94 Consumerproducls@Panasonic cam ENGLISH □ ÜTGD653B seoecnsa...